Summary:
When paranoid_checks is on, DBImpl::CheckConsistency() iterates over all sst files and calls Env::GetFileSize() for each of them. As far as I could understand, this is pretty arbitrary and doesn't affect correctness - if filesystem doesn't corrupt fsynced files, the file sizes will always match; if it does, it may as well corrupt contents as well as sizes, and rocksdb doesn't check contents on open.
If there are thousands of sst files, getting all their sizes takes a while. If, on top of that, Env is overridden to use some remote storage instead of local filesystem, it can be *really* slow and overload the remote storage service. This PR adds an option to not do GetFileSize(); instead it does GetChildren() for parent directory to check that all the expected sst files are at least present, but doesn't check their sizes.
We can't just disable paranoid_checks instead because paranoid_checks do a few other important things: make the DB read-only on write errors, print error messages on read errors, etc.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/6353
Test Plan: ran the added sanity check unit test. Will try it out in a LogDevice test cluster where the GetFileSize() calls are causing a lot of trouble.
Differential Revision: D19656425
Pulled By: al13n321
fbshipit-source-id: c2c421b367633033760d1f56747bad206d1fbf82
Summary:
In WritePrepared there could be gap in sequence numbers. This breaks the trick we use in kPointInTimeRecovery which assume the first seq in the log right after the corrupted log is one larger than the last seq we read from the logs. To let this trick keep working, we add a dummy entry with the expected sequence to the first log right after recovery.
Also in WriteCommitted, if the log right after the corrupted log is empty, since it has no sequence number to let the sequential trick work, it is assumed as unexpected behavior. This is however expected to happen if we close the db after recovering from a corruption and before writing anything new to it. To remedy that, we apply the same technique by writing a dummy entry to the log that is created after the corrupted log.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/6313
Differential Revision: D19458291
Pulled By: maysamyabandeh
fbshipit-source-id: 09bc49e574690085df45b034ca863ff315937e2d
Summary:
I found that CleanupSuperVersion() may block Get() for 30ms+ （per MemTable is 256MB）.
Then I found "delete sv" in ~SuperVersion() takes the time.
The backtrace looks like this
DBImpl::GetImpl() -> DBImpl::ReturnAndCleanupSuperVersion() ->
DBImpl::CleanupSuperVersion() : delete sv; -> ~SuperVersion()
I think it's better to delete in a background thread, please review it。
Pull Request resolved: https://github.com/facebook/rocksdb/pull/6146
Differential Revision: D18972066
fbshipit-source-id: 0f7b0b70b9bb1e27ad6fc1c8a408fbbf237ae08c
Summary:
The current Env API encompasses both storage/file operations, as well as OS related operations. Most of the APIs return a Status, which does not have enough metadata about an error, such as whether its retry-able or not, scope (i.e fault domain) of the error etc., that may be required in order to properly handle a storage error. The file APIs also do not provide enough control over the IO SLA, such as timeout, prioritization, hinting about placement and redundancy etc.
This PR separates out the file/storage APIs from Env into a new FileSystem class. The APIs are updated to return an IOStatus with metadata about the error, as well as to take an IOOptions structure as input in order to allow more control over the IO.
The user can set both ```options.env``` and ```options.file_system``` to specify that RocksDB should use the former for OS related operations and the latter for storage operations. Internally, a ```CompositeEnvWrapper``` has been introduced that inherits from ```Env``` and redirects individual methods to either an ```Env``` implementation or the ```FileSystem``` as appropriate. When options are sanitized during ```DB::Open```, ```options.env``` is replaced with a newly allocated ```CompositeEnvWrapper``` instance if both env and file_system have been specified. This way, the rest of the RocksDB code can continue to function as before.
This PR also ports PosixEnv to the new API by splitting it into two - PosixEnv and PosixFileSystem. PosixEnv is defined as a sub-class of CompositeEnvWrapper, and threading/time functions are overridden with Posix specific implementations in order to avoid an extra level of indirection.
The ```CompositeEnvWrapper``` translates ```IOStatus``` return code to ```Status```, and sets the severity to ```kSoftError``` if the io_status is retryable. The error handling code in RocksDB can then recover the DB automatically.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5761
Differential Revision: D18868376
Pulled By: anand1976
fbshipit-source-id: 39efe18a162ea746fabac6360ff529baba48486f
Summary:
After secondary instance replays the logs from primary, certain files become
obsolete. The secondary should find these files, evict their table readers from
table cache and close them. If this is not done, the secondary will hold on to
these files and prevent their space from being freed.
Test plan (devserver):
```
$./db_secondary_test --gtest_filter=DBSecondaryTest.SecondaryCloseFiles
$make check
$./db_stress -ops_per_thread=100000 -enable_secondary=true -threads=32 -secondary_catch_up_one_in=10000 -clear_column_family_one_in=1000 -reopen=100
```
Pull Request resolved: https://github.com/facebook/rocksdb/pull/6114
Differential Revision: D18769998
Pulled By: riversand963
fbshipit-source-id: 5d1f151567247196164e1b79d8402fa2045b9120
Summary:
Further apply formatter to more recent commits.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5830
Test Plan: Run all existing tests.
Differential Revision: D17488031
fbshipit-source-id: 137458fd94d56dd271b8b40c522b03036943a2ab
Summary:
Move definition and implementation for ArenaWrappedDBIter into its own .h/.cc files. Also, change inlining of functions to better comply with the Google C++ style guide.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5801
Test Plan: make check
Differential Revision: D17371012
Pulled By: anand1976
fbshipit-source-id: c1361abc2851575111e357a63d88be3b3d6cb341
Summary:
MyRocks currently sets `max_write_buffer_number_to_maintain` in order to maintain enough history for transaction conflict checking. The effectiveness of this approach depends on the size of memtables. When memtables are small, it may not keep enough history; when memtables are large, this may consume too much memory.
We are proposing a new way to configure memtable list history: by limiting the memory usage of immutable memtables. The new option is `max_write_buffer_size_to_maintain` and it will take precedence over the old `max_write_buffer_number_to_maintain` if they are both set to non-zero values. The new option accounts for the total memory usage of flushed immutable memtables and mutable memtable. When the total usage exceeds the limit, RocksDB may start dropping immutable memtables (which is also called trimming history), starting from the oldest one.
The semantics of the old option actually works both as an upper bound and lower bound. History trimming will start if number of immutable memtables exceeds the limit, but it will never go below (limit-1) due to history trimming.
In order the mimic the behavior with the new option, history trimming will stop if dropping the next immutable memtable causes the total memory usage go below the size limit. For example, assuming the size limit is set to 64MB, and there are 3 immutable memtables with sizes of 20, 30, 30. Although the total memory usage is 80MB > 64MB, dropping the oldest memtable will reduce the memory usage to 60MB < 64MB, so in this case no memtable will be dropped.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5022
Differential Revision: D14394062
Pulled By: miasantreble
fbshipit-source-id: 60457a509c6af89d0993f988c9b5c2aa9e45f5c5
Summary:
Added log_readahead_size option to control prefetching for Log::Reader.
This is mostly useful for reading a remotely located log, as it can save the number of round-trips when reading it.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5592
Differential Revision: D16362989
Pulled By: elipoz
fbshipit-source-id: c5d4d5245a44008cd59879640efff70c091ad3e8
Summary:
`DBImplSecondary` calls `CheckConsistency()` during open. In the past, `DBImplSecondary` did not override this function thus `DBImpl::CheckConsistency()` is called.
The following can happen. The secondary instance is performing consistency check which calls `GetFileSize(file_path)` but the file at `file_path` is deleted by the primary instance. `DBImpl::CheckConsistency` does not account for this and fails the consistency check. This is undesirable. The solution is that, we call `DBImpl::CheckConsistency()` first. If it passes, then we are good. If not, we give it a second chance and handles the case of file(s) being deleted.
Test plan (on dev server):
```
$make clean && make -j20 all
$./db_secondary_test
```
All other existing unit tests must pass as well.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5469
Differential Revision: D15861845
Pulled By: riversand963
fbshipit-source-id: 507d72392508caed3cd003bb2e2aa43f993dd597
Summary:
In secondary mode, it is possible that the secondary lists the primary's WAL
directory, finds a WAL and tries to open it. It is possible that the primary
deletes the WAL after secondary listing dir but before the secondary opening
it. Then the secondary will fail to open the WAL file with a PathNotFound
status. In this case, we can return OK without replaying WAL and optionally
replay more MANIFEST.
Test Plan (on my dev machine):
Without this PR, the following will fail several times out of 100 runs.
```
~/gtest-parallel/gtest-parallel -r 100 -w 16 ./db_secondary_test --gtest_filter=DBSecondaryTest.SwitchToNewManifestDuringOpen
```
With this PR, the above should always succeed.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5323
Differential Revision: D15763878
Pulled By: riversand963
fbshipit-source-id: c7164fa7cb8d9001abc258b6a2dc93613e4f38ff
Summary:
Use `CreateLoggerFromOptions` function to reduce code duplication.
Test plan (on my machine)
```
$make clean && make -j32 db_secondary_test
$KEEP_DB=1 ./db_secondary_test
```
Verify all info logs of the secondary instance are properly logged.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5427
Differential Revision: D15748922
Pulled By: riversand963
fbshipit-source-id: bad7261df1b8373efc504f141efc7871e375a311
Summary:
In regular RocksDB instance, `MemTable::earliest_seqno_` is "db sequence number at the time of creation". However, we cannot use the db sequence number to set the value of `MemTable::earliest_seqno_` for secondary instance, i.e. `DBImplSecondary` due to the logic of MANIFEST and WAL replay.
When replaying the log files of the primary, the secondary instance first replays MANIFEST and updates the db sequence number if necessary. Next, the secondary replays WAL files, creates new memtables if necessary and inserts key-value pairs into memtables. The following can occur when the db has two or more column families.
Assume the db has column family "default" and "cf1". At a certain in time, both "default" and "cf1" have data in memtables.
1. Primary triggers a flush and flushes "cf1". "default" is **not** flushed.
2. Secondary replays the MANIFEST updates its db sequence number to the latest value learned from the MANIFEST.
3. Secondary starts to replay WAL that contains the writes to "default". It is possible that the write batches' sequence numbers are smaller than the db sequence number. In this case, these write batches will be skipped, and these updates will not be visible to reader until "default" is later flushed.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5413
Differential Revision: D15637407
Pulled By: riversand963
fbshipit-source-id: 3de3fe35cfc6f1b9f844f3f926f0df29717b6580
Summary:
When using `PRIu64` type of printf specifier, current code base does the following:
```
#ifndef __STDC_FORMAT_MACROS
#define __STDC_FORMAT_MACROS
#endif
#include <inttypes.h>
```
However, this can be simplified to
```
#include <cinttypes>
```
as long as flag `-std=c++11` is used.
This should solve issues like https://github.com/facebook/rocksdb/issues/5159
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5402
Differential Revision: D15701195
Pulled By: miasantreble
fbshipit-source-id: 6dac0a05f52aadb55e9728038599d3d2e4b59d03
Summary:
Many logging related source files are under util/. It will be more structured if they are together.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5387
Differential Revision: D15579036
Pulled By: siying
fbshipit-source-id: 3850134ed50b8c0bb40a0c8ae1f184fa4081303f
