Summary:
MyRocks currently sets `max_write_buffer_number_to_maintain` in order to maintain enough history for transaction conflict checking. The effectiveness of this approach depends on the size of memtables. When memtables are small, it may not keep enough history; when memtables are large, this may consume too much memory.
We are proposing a new way to configure memtable list history: by limiting the memory usage of immutable memtables. The new option is `max_write_buffer_size_to_maintain` and it will take precedence over the old `max_write_buffer_number_to_maintain` if they are both set to non-zero values. The new option accounts for the total memory usage of flushed immutable memtables and mutable memtable. When the total usage exceeds the limit, RocksDB may start dropping immutable memtables (which is also called trimming history), starting from the oldest one.
The semantics of the old option actually works both as an upper bound and lower bound. History trimming will start if number of immutable memtables exceeds the limit, but it will never go below (limit-1) due to history trimming.
In order the mimic the behavior with the new option, history trimming will stop if dropping the next immutable memtable causes the total memory usage go below the size limit. For example, assuming the size limit is set to 64MB, and there are 3 immutable memtables with sizes of 20, 30, 30. Although the total memory usage is 80MB > 64MB, dropping the oldest memtable will reduce the memory usage to 60MB < 64MB, so in this case no memtable will be dropped.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5022
Differential Revision: D14394062
Pulled By: miasantreble
fbshipit-source-id: 60457a509c6af89d0993f988c9b5c2aa9e45f5c5
Summary:
Current PosixLogger performs IO operations using posix calls. Thus the
current implementation will not work for non-posix env. Created a new
logger class EnvLogger that uses env specific WritableFileWriter for IO operations.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5491
Test Plan: make check
Differential Revision: D15909002
Pulled By: ggaurav28
fbshipit-source-id: 13a8105176e8e42db0c59798d48cb6a0dbccc965
Summary:
The first key is used to defer reading the data block until this file gets to the top of merging iterator's heap. For short range scans, most files never make it to the top of the heap, so this change can reduce read amplification by a lot sometimes.
Consider the following workload. There are a few data streams (we'll be calling them "logs"), each stream consisting of a sequence of blobs (we'll be calling them "records"). Each record is identified by log ID and a sequence number within the log. RocksDB key is concatenation of log ID and sequence number (big endian). Reads are mostly relatively short range scans, each within a single log. Writes are mostly sequential for each log, but writes to different logs are randomly interleaved. Compactions are disabled; instead, when we accumulate a few tens of sst files, we create a new column family and start writing to it.
So, a typical sst file consists of a few ranges of blocks, each range corresponding to one log ID (we use FlushBlockPolicy to cut blocks at log boundaries). A typical read would go like this. First, iterator Seek() reads one block from each sst file. Then a series of Next()s move through one sst file (since writes to each log are mostly sequential) until the subiterator reaches the end of this log in this sst file; then Next() switches to the next sst file and reads sequentially from that, and so on. Often a range scan will only return records from a small number of blocks in small number of sst files; in this case, the cost of initial Seek() reading one block from each file may be bigger than the cost of reading the actually useful blocks.
Neither iterate_upper_bound nor bloom filters can prevent reading one block from each file in Seek(). But this PR can: if the index contains first key from each block, we don't have to read the block until this block actually makes it to the top of merging iterator's heap, so for short range scans we won't read any blocks from most of the sst files.
This PR does the deferred block loading inside value() call. This is not ideal: there's no good way to report an IO error from inside value(). As discussed with siying offline, it would probably be better to change InternalIterator's interface to explicitly fetch deferred value and get status. I'll do it in a separate PR.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5289
Differential Revision: D15256423
Pulled By: al13n321
fbshipit-source-id: 750e4c39ce88e8d41662f701cf6275d9388ba46a
Summary:
Currently we validate options in DB::Open. However the validation step is missing when options are dynamically updated in ::SetOptions. The patch fixes that.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5368
Differential Revision: D15540101
Pulled By: maysamyabandeh
fbshipit-source-id: d27bbffd8f0252d1b50bcf59e0a70a278ed937f4
Summary:
There are too many types of files under util/. Some test related files don't belong to there or just are just loosely related. Mo
ve them to a new directory test_util/, so that util/ is cleaner.
Pull Request resolved: https://github.com/facebook/rocksdb/pull/5377
Differential Revision: D15551366
Pulled By: siying
fbshipit-source-id: 0f5c8653832354ef8caa31749c0143815d719e2c
