If foundScreen is TRUE, then all the code below the removed if
will not execute until we reach the return foundScreen; at the
end, so this entire if block is redundant.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
xf86CheckHWCursor() would dereference sPriv without NULL checking it. If Option
"SWCursor" is specified, sPriv == NULL. In this case we should assume that HW
cursors are not supported.
Signed-off-by: Alex Goins <agoins@nvidia.com>
Reviewed-by: Andy Ritger <aritger@nvidia.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Commit c7e8d4a6ee had already unifdef
MODESETTING_OUTPUT_SLAVE_SUPPORT but commit
9257b1252d didn't notice that.
Signed-off-by: Nikhil Mahale <nmahale@nvidia.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Prior to this commit the Xorg.wrap code to detect if root rights are
necessary checked for DRM_IOCTL_MODE_GETRESOURCES succeeding *and*
reporting more then 0 output connectors.
DRM_IOCTL_MODE_GETRESOURCES succeeding alone is enough to differentiate
between old drm only cards (which need ums and thus root) and kms capable
cards.
Some hybrid gfx laptops have 0 output connectors on one of their 2 GPUs,
resulting in Xorg needlessly running as root. This commits removes the
res.count_connectors > 0 check, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
Fixes DRI2 client driver name mapping for newer AMD GPUs with the
modesetting driver, allowing the DRI2 extension to initialize.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a missing ifdef needed for --disable-glamor.
Signed-off-by: Mihail Konev <k.mvc@ya.ru>
Reviewed-by: Jon Turney <jon.turney@dronecode.org.uk>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Special case for the systemd-logind case in xfree86: when we're vt-switched
away and a device is plugged in, we get a paused fd from logind. Since we
can't probe the device or do anything with it, we store that device in the
xfree86 and handle it later when we vt-switch back. The device is not added to
inputInfo.devices until that time.
When the device is removed while still vt-switched away, the the config system
never notifies the DDX. It only runs through inputInfo.devices and our device
was never added to that.
When a device is plugged in, removed, and plugged in again while vt-switched
away, we have two entries in the xfree86-specific list that refer to the same
device node, both pending for addition later. On VT switch back, the first one
(the already removed one) will be added successfully, the second one (the
still plugged-in one) fails. Since the fd is correct, the device works until
it is removed again. The removed devices' config_info (i.e. the syspath)
doesn't match the actual device we addded tough (the input number increases
with each plug), it doesn't get removed, the fd remains open and we lose track
of the fd count. Plugging the device in again leads to a dead device.
Fix this by adding a call to notify the DDX to purge any remainders of devices
with the given config_info, that's the only identifiable bit we have at this
point.
https://bugs.freedesktop.org/show_bug.cgi?id=97928
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
No functional changes but it makes it easier to remove elements from the
middle of the list (future patch).
We don't have an init call into this file, so the list is manually
initialized.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
They're identically laid-out structs but let's use the right type to search
for our desired value.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Prevents the HW cursor from intermittently jumping around when the
cursor image is changed while the cursor is being moved. This is hardly
noticeable in normal operation but can be quite confusing when stepping
through these codepaths in a debugger.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
xf86CursorScreenRec::HotX/Y contain 0 for PRIME slave screens.
Fixes incorrect HW cursor position on PRIME slave screens.
Also hoist the hotspot translation out from xf86ScreenSet/MoveCursor to
xf86Set/MoveCursor, since the hotspot position is a property of the
cursor, not the screen.
v2:
* Squash patches 1 & 2 of the v1 series, since it's basically the same
problem
* Use the master screen's xf86CursorScreenRec::HotX/Y instead of
CursorRec::bits->x/yhot, since CursorRec::bits can be NULL (Hans de
Goede)
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
As of last commit all the places in our configure.ac require version
2.3.1 (released back in 2007) or later. With the latter introducing the
1.3.0 version, as returned by drmGetLibVersion.
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Presently the option guards both direct and accelerated indirect GLX. As
such when one toggles it off they end up without any acceleration.
Remove the option all together until we have the time to split/rework
things.
Cc: Jon Turney <jon.turney@dronecode.org.uk>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
The option is misleading and using it leads to disabling both direct and
accelerated indirect GLX. In such cases the xserver GLX attempts to
match DRISW (IGLX) configs with the DRI2/3 ones (direct GLX) leading to
all sorts of fun experience.
Remove the option until we get a clear split and control over direct vs
indirect GLX.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
This change effectively reverts commit 074cf58. We were falling back from
drmModeSetCursor2() to drmModeSetCursor() whenever the first failed. This
fall-back only makes sense on pre-mid-2013 kernels which implemented the
cursor_set hook but not cursor_set2, and in this case the call to
drmModeSetCursor2() will always return -EINVAL. Specifically, a return
value of -ENXIO usually means that neither are supported.
Signed-off-by: Michael Thayer <michael.thayer@oracle.com>
[hdegoede@redhat.com: initialize ret to -EINVAL]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We get multiple udev events for actions like docking a laptop into its
station or plugging a monitor to the station. By consuming as much
events as we can, we reduce the number of output re-evalutions.
I.e. having a Lenovo X250 in a ThinkPad Ultra Dock and plugging a
monitor to the station generates 5 udev events. Or having 2 monitors
attached to the station and docking the laptop generates 7 events.
It depends on the timing how many events can consumed at once.
Signed-off-by: Daniel Martin <consume.noise@gmail.com>
[hdegoede@redhat.com: Keep goto out so that we always call RRGetInfo()]
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This fix is for the following xorg.conf can work:
Section "ServerFlags"
Option "AutoAddGPU" "off"
EndSection
Section "Device"
Identifier "Amd"
Driver "ati"
BusID "PCI:1:0:0"
EndSection
Section "Device"
Identifier "Intel"
Driver "modesetting"
BusID "pci:0:2:0"
EndSection
Section "Screen"
Identifier "Screen0"
Device "Intel"
GPUDevice "Amd"
EndSection
Without AutoAddGPU off, modesetting DDX will also be loaded
for GPUDevice.
Signed-off-by: Qiang Yu <Qiang.Yu@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The new platform bus code and the old PCI bus code overlap. Platform bus
can handle any type of device, including PCI devices, whereas the PCI code
can only handle PCI devices. Some drivers only support the old style
PCI-probe methods, but the primary device detection code is server based,
not driver based; so we might end up with a primary device which only has
a PCI bus-capable driver, but was detected as primary by the platform
code, or the other way around.
(The above paragraph was shamelessly stolen from Hans de Goede, and
customized.)
The latter case applies to QEMU's virtio-gpu-pci device: it is detected as
a BUS_PCI primary device, but we actually probe it first (with the
modesetting driver) through xf86platformProbeDev(). The
xf86IsPrimaryPlatform() function doesn't recognize the device as primary
(it bails out as soon as it sees BUS_PCI); instead, we add the device as a
secondary graphics card under "autoAddGPU". In turn, the success of this
automatic probing-as-GPU prevents xf86CallDriverProbe() from proceeding to
the PCI probing.
The result is that the server exits with no primary devices detected.
Commit cf66471353 ("xfree86: use udev to provide device enumeration for
kms devices (v10)") added "cross-bus" matching to xf86IsPrimaryPci(). Port
that now to xf86IsPrimaryPlatform(), so that we can probe virtio-gpu-pci
as a primary card in platform bus code.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Cc: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Tested-By: Marcin Juszkiewicz <mjuszkiewicz@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=93675
Signed-off-by: Kyle Guinn <elyk03@gmail.com>
[hdegoede@redhat.com: Simplify by adding 2 if conds together with &&]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A couple of memory leaks fixes and avoiding bit shifting on an
unitialized value.
[hdegoede@redhat.com: Split out some non free fixes in separate patches]
[hdegoede@redhat.com: Don't touch ancient (and weird) os/rpcauth.c code]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Commit b4e46c0444 ("xfree86: Hook up colormaps and RandR 1.2 gamma code")
dropped the providing of a pScrn->ChangeGamma callback from the xf86RandR12
code. Leaving pScrn->ChangeGamma NULL in most cases.
This triggers the BadImplementation error in xf86ChangeGamma() :
if (pScrn->ChangeGamma)
return (*pScrn->ChangeGamma) (pScrn, gamma);
return BadImplementation;
Which causes X-apps using XF86VidModeSetGamma to crash with a
X protocol error.
This commit fixes this by re-introducing the xf86RandR12ChangeGamma
helper removed by the commit and adjusting it to work with the new
combined palette / gamma code.
Fixes: b4e46c0444 ("xfree86: Hook up colormaps and RandR 1.2 gamma code")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
This is a preparation patch to allow easier usage of init_one_component
outside of xf86RandR12CrtcInitGamma.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
When using secondary GPU outputs the primary GPU's blockhandler
will copy changes from its framebuffer to a pixmap shared with the
secondary GPU.
In reverse prime setups the secondary GPU's blockhandler will do another
copy from the shared pixmap to its own framebuffer.
Before this commit, if the primary GPU's blockhandler would run after
the secondary GPU's blockhandler and no events were pending, then the
secondary GPU's blockhandler would not run until some events came in
(WaitForSomething() would block in the poll call), resulting in the
secondary GPU output sometimes showing stale contents (e.g. a just closed
window) for easily up to 10 seconds.
This commit fixes this by setting the timeout passed into the
blockhandler to 0 if any shared pixmaps were updated by the primary GPU,
forcing an immediate re-run of all blockhandlers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
When using reverse prime we do 2 copies, 1 from the primary GPU's
framebuffer to a shared pixmap and 1 from the shared pixmap to the
secondary GPU's framebuffer.
This means that on the primary GPU side the copy MUST be finished,
before we start the second copy (before the secondary GPU's driver
starts processing the damage on the shared pixmap).
This fixes secondary outputs sometimes showning (some) old fb contents,
because of the 2 copies racing with each other, for an example of
what this looks like see:
https://fedorapeople.org/~jwrdegoede/IMG_20160915_130555.jpg
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Fixes XRRGetOutputPrimary and xrandr not reporting a primary output after
startup. This was especially confusing when an output was explicitly
marked as primary using Option "Primary" in Section "Monitor".
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Move ms_flush_drm_events out of GLAMOR ifdef.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97586
Signed-off-by: Qiang Yu <Qiang.Yu@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
This fixes glxgears running at 1 fps when fully covering a slave-output
and the modesetting driver is used for the master gpu.
Reported-by: Peter Wu <peter@lekensteyn.nl>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
99% of the code in ms_covering_crtc is video-driver agnostic. Add a
screen_is_ms parameter when when FALSE skips the one ms specific check,
this will allow calling ms_covering_crtc on slave GPUs.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Implement the CreateBuffer2 / DestroyBuffer2 / CopyRegion2 DRI2InfoRec
version 9 callbacks, this is necessary for being an offload source
provider with DRI2.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
If a frontbuffer drawable already has a pixmap, make sure it was created
on the right screen.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently with PRIME if we detect a secondary GPU,
we switch to using SW cursors, this isn't optimal,
esp for the intel/nvidia combinations, we have
no choice for the USB offload devices.
This patch checks on each slave screen if hw
cursors are enabled, and also calls set cursor
and move cursor on all screens.
Cc: Aaron Plattner <aplattner@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
When a slave-output is rotated the transformation is done on the blit
from master to slave GPU, so crtc->transform_in_use is not set, but we
still need to adjust the mouse position for things to work.
This commit modifies xf86_crtc_transform_cursor_position to not rely
on crtc->f_framebuffer_to_crtc, so that it can be used with GPU screens
too and always calls it for crtcs with any form of rotation.
Note not using crtc->f_framebuffer_to_crtc means that crtc->transform
will not be taken into account, that is ok, because when we've a transform
active hw-cursors are not used and xf86_crtc_transform_cursor_position
will never get called.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-and-Tested-by: Michel Dänzer <michel.daenzer@amd.com>
xf86_crtc_rotate_coord should be the exact inverse operation of
xf86_crtc_rotate_coord_back, but when calculating x / y for 90 / 270
degrees rotation it was using height to calculate x / width to calculate y,
instead of the otherway around.
This was likely not noticed before since xf86_crtc_rotate_coord
until now was only used with cursor_info->MaxWidth and
cursor_info->MaxHeight, which are usally the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
The CurrentCursor is always attached to the master GPU.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
This is a preparation patch for adding prime hw-cursor support.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
The "if (pixmap) ..." block this commit removes is inside an
"if (pixmap == NULL) ..." block, so it will never execute.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Aaron Plattner <aplattner@nvidia.com>
Remove unused arguments from ms_covering_crtc, make it static as it is
only used in vblank.c.
While at it also change its first argument from a ScrnInfoPtr to a
ScreenPtr, this makes the next patch in this patch-set cleaner.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
glamor_fd_from_pixmap() may return a tiled bo, which is not suitable
for sharing with another GPU as tiling usually is GPU specific.
Switch to glamor_shareable_fd_from_pixmap(), which always returns a
linear bo. This fixes mis-rendering when running the mode setting
driver on the master gpu in a dual-gpu setup and running an opengl
app with DRI_PRIME=1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
The common page flip handle framework can be shared with DRI2
page flip.
Signed-off-by: Qiang Yu <Qiang.Yu@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
When Xorg gets started directly from a wayland-gdm the crtc still has the
wayland hw cursor set. Combine this with Xorg immediately falling back to
a sw cursor because a slave-output has a monitor attached at startup; and
we end up with the wayland hardware cursor overlay fixed in its last
position + the Xorg sw cursor resulting in 2 cursors.
This commit fixes this by hiding any left-over cursors when initializing
the crtc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Eric Engestrom <eric.engestrom@imgtec.com>
The modesetting driver may be driving 2 screens (slave and master
gpu), which may have different behavior wrt hardware cursor support.
So stop using static variables and instead store the hw-cursor support
related data in a per screen struct. While at it actually make it per
crtc data as in theory different crtc's could have different hw-cursor
support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
We're happily printing the error to stdout but not which module caused it...
That's in the Xorg.log but that's at least one click away.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Xorg -configure relies on the bus implementation, e.g.
xf86pciBus.c to call xf86AddBusDeviceToConfigure(). The new
xf86platformBus code does not have support for this.
Almost all drivers support both the xf86platformBus and xf86pciBus
nowadays, and the generic xf86Bus xf86CallDriverProbe() function
prefers the new xf86platformBus probe method when available.
Since the platformBus paths do not call xf86AddBusDeviceToConfigure()
this results in Xorg -configure failing with the following error:
"No devices to configure. Configuration failed.".
Adding support for the xf86Configure code to xf86platformBus.c
is non trivial and since we advise users to normally run without
any Xorg.conf at all not worth the trouble.
However some users still want to use Xorg -configure to generate a
template config file, this commit implements a minimal fix to make
things work again for PCI devices by skipping the platform
probe method when xf86DoConfigure is set.
This has been tested on a system with integrated intel graphics,
with both the intel and modesetting drivers and restores Xorg -configure
functionality on both cases.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This loop was written in a buggy style, causing a NULL driver ptr to be
passed to copyScreen(). copyScreen() only uses that to generate an
identifier string, so this is mostly harmless on systems that accept
NULL for asprintf() "%s" format. (the generated identifiers are off
by one wrt the driver names and the last one contains NULL.
For systems that don't accept NULL for '%s' this would cause a
segmentation fault when this code is used (no xorg.conf, but partial
config in xorg.conf.d for instance).
Signed-off-by: Matthieu Herrb <matthieu@herrb.eu>
Reviewed-by: Keith Packard <keithp@keithp.com>
