First mode is _always_ preferred in 1.4; the bit that used to mean this
now means that the preferred mode is also the native pixel format. The
old "is GTF" bit now means "is continuous-frequency" instead.
Section 3.6.4, Table 3.14: Feature Support, Notes 4 and 5.
Nothing actually decoded yet, but at least we print what they are.
New in EDID 1.4:
- Color Management Data (0xF9), Section 3.10.3.7
- CVT 3 Byte Code Descriptor (0xF8), Section 3.10.3.8
- Established Timings III Descriptor (0xF7), section 3.10.3.9
- Manufacturer-specified data tag (0x00 - 0x0F), section 3.10.3.12
Even though they're defined to zero by the spec, we've seen an EDID block
where the (empty) ASCII strings were stuffed in a byte early, leading to the
descriptor being considered a detailed timing instead.
I made a mistake in some new code using MakeAtom, passing the size of the
string instead of the length of the string. Figuring there might be other
such mistakes, I reviewed the server code and found four bugs of the same
form.
The DDC code sets the I2C timeouts to VESA standards, except that it had an
extra setting of the ByteTimeout value which was wrong (off by a factor of
50). Removing this should help DDC work on many more monitors. Note that the
Intel driver duplicated these settings, along with the error. Yay for cult
and paste coding.
Code added in hw/xfree86/modes came from the server-1.3-branch.
Portions of this code had previously been integrated into xf86Mode.c
and edid_modes.c.
To preserve hw/xfree86/modes as much as possible, the duplicate code from
the other files has been disabled; a more careful review would figure out
where that code actually belonged.
This code comes from the intel driver, so there's no history in this tree.
As the crtc/output-based mode selection code uses ddc, the ddc and i2c
modules have been merged into the server. Attempts to load them are safely
ignored now.
CFLAGS is a user variable, extracted from the environment at configure time
and settable by the user at build time. We must not override this variable.
This allows the server to guess an appropriate initial virtual size and
resolution. The heuristic is to select the largest driver-reported mode
that matches the monitor's physical aspect ratio. We revalidate this
estimate after mode validation, since we may have filtered away all
modes that would fill that size.
Also, the EDID preferred timing is now marked as M_T_PREFERRED as well.
Base EDID only lets you specify the maximum dotclock in tens of MHz, which
is too fuzzy for some monitors. 1600x1200@60 is just over 160MHz, but if
the monitor really can't handle any mode at 170MHz, then 160 is more
correct. Fix up the EDID block before the driver can see it in this case,
so we don't spuriously reject modes.
The X gamma is used to set the output ramp of the card. Setting a 2.2 output
gamma going into a 2.2 monitor gives an effective gamma of 4.84, which is
very much not what you want.
Get rid of almost all uses of these definitions. They're still defined for
delinquent out-of-tree drivers, and also for the Mesa build. As well as
for miinitext.c. But largely gone.
XFree86LOADER ifdefs, non-loadable hasn't been supported for a while
now. Remove completely gratuitious REMOVE_LOADER_CHECK_MODULE_INFO
ifdefs surrounding a call to a function added in XFree86 4.1 (!).
Miscellaneous static markings.
Add XSERV_t, TRANS_SERVER, TRANS_REOPEN to quash warnings.
Add #include <dix-config.h> or <xorg-config.h>, as appropriate, to all
source files in the xserver/xorg tree, predicated on defines of
HAVE_{DIX,XORG}_CONFIG_H. Change all Xfont includes to
<X11/fonts/foo.h>.
change "foo.h" to <X11/foo.h> for core headers, e.g. X.h, Xpoll.h;
change "foo.h", "extensions/foo.h" and "X11/foo.h" to
<X11/extensions/foo.h> for extension headers, e.g. Xv.h;
change "foo.[ch]" to <X11/Xtrans/foo.[ch]> for Xtrans files.
Updating to EDID 1.3. (Bugzilla# 1490, Jay Cotton, Egbert Eich).
Removing unneeded code.
Fixed KGA handling for i810. KGA handling for chips derived from C&T chips
is slightly different. The changes make the code consistent with the
C&T (chips) and i740 drivers.