Commit Graph

1961 Commits

Author SHA1 Message Date
Norman Maurer
57e7571c65 Not trigger channelWritabilityChanged if fail messages before close Channel.
Motivation:

We should not trigger channelWritabilityChanged during failing message when we are about to close the Channel as otherwise the use may try again writing even if the Channel is about to get closed.

Modifications:

Add new boolean param to ChannelOutboundBuffer.failFlushed(...) which allows to specify if we should notify or not.

Result:

channelWritabilityChanged is not triggered anymore if we cloe the Channel because of an IOException during write.
2015-05-06 21:36:43 +02:00
Norman Maurer
f839f65c15 Do not defer closing of Channel when in flush
Motivation:

Previously, we deferred the closing of the Channel when we were flushing. This is problematic as this means that if the user adds a ChannelFutureListener, that will close the Channel, the closing will not happen until we are done with flushing. This can lead to more data is sent than expected.

Modifications:

- Do not defer closing when in flush

Result:

Correctly respect order of events and closing the Channel ASAP
2015-05-06 21:07:10 +02:00
Norman Maurer
e276cb796c Correct semantic of LocalChannel.doWrite(...) and remove memory copy
Motivation:

The semantic of LocalChannel.doWrite(...) were a bit off as it notified the ChannelFuture before the data was actual moved to the peer buffer.

Modifications:

- Use our MPSC queue as inbound buffer
- Directly copy to data to the inbound buffer of the peer and either success or fail the promise after each copy.

Result:

Correct semantic and less memory copies.
2015-05-06 10:44:31 +02:00
Scott Mitchell
c94e7f744a DefaultChannelPipeline needs to release objects
Motiviation:
If user events or excpetions reach the tail end of the pipeline they are not released. This could result in buffer leaks.

Motivation:
- Use the ReferenceCountUtil.release to release objects for the userEventTriggered and exceptionCaught methods on DefaultChannelPipeline

Result:
2 less areas where buffer leaks can occur.
2015-05-06 06:46:52 +02:00
Trustin Lee
63a02fc04e Revamp DNS codec
Motivation:

There are various known issues in netty-codec-dns:

- Message types are not interfaces, which can make it difficult for a
  user to implement his/her own message implementation.
- Some class names and field names do not match with the terms in the
  RFC.
- The support for decoding a DNS record was limited. A user had to
  encode and decode by him/herself.
- The separation of DnsHeader from DnsMessage was unnecessary, although
  it is fine conceptually.
- Buffer leak caused by DnsMessage was difficult to analyze, because the
  leak detector tracks down the underlying ByteBuf rather than the
  DnsMessage itself.
- DnsMessage assumes DNS-over-UDP.
- To send an EDNS message, a user have to create a new DNS record class
  instance unnecessarily.

Modifications:

- Make all message types interfaces and add default implementations
- Rename some classes, properties, and constants to match the RFCs
  - DnsResource -> DnsRecord
  - DnsType -> DnsRecordType
  - and many more
- Remove DnsClass and use an integer to support EDNS better
- Add DnsRecordEncoder/DnsRecordDecoder and their default
  implementations
  - DnsRecord does not require RDATA to be ByteBuf anymore.
  - Add DnsRawRecord as the catch-all record type
- Merge DnsHeader into DnsMessage
- Make ResourceLeakDetector track AbstractDnsMessage
- Remove DnsMessage.sender/recipient properties
  - Wrap DnsMessage with AddressedEnvelope
  - Add DatagramDnsQuest and DatagramDnsResponse for ease of use
  - Rename DnsQueryEncoder to DatagramDnsQueryEncoder
  - Rename DnsResponseDecoder to DatagramDnsResponseDecoder
- Miscellaneous changes
  - Add StringUtil.TAB

Result:

- Cleaner APi
- Can support DNS-over-TCP more easily in the future
- Reduced memory footprint in the default DnsQuery/Response
  implementations
- Better leak tracking for DnsMessages
- Possibility to introduce new DnsRecord types in the future and provide
  full record encoder/decoder implementation.
- No unnecessary instantiation for an EDNS pseudo resource record
2015-05-01 11:33:16 +09:00
Norman Maurer
56c98839c3 [#3218] Add ChannelPool / ChannelPoolMap abstraction and implementations
Motivation:

Many projects need some kind a Channel/Connection pool implementation. While the protocols are different many things can be shared, so we should provide a generic API and implementation.

Modifications:

Add ChannelPool / ChannelPoolMap API and implementations.

Result:

Reusable / Generic pool implementation that users can use.
2015-04-30 12:13:19 +02:00
Norman Maurer
1cce998bb0 [#3662] Fail the connect future on close
Motivation:

Because of a bug we missed to fail the connect future when doClose() is called. This can lead to a future which is never notified and so may lead to deadlocks in user-programs.

Modifications:

Correctly fail the connect future when doClose() is called and the connection was not established yet.

Result:

Connect future is always notified.
2015-04-27 20:05:00 +02:00
Norman Maurer
ccde870b38 Revert "Ensure channelReadComplete() is called only when necessary"
This reverts commit 27a25e29f7.
2015-04-20 09:10:41 +02:00
Norman Maurer
bb692816d2 Revert "Do not suppress channelReadComplete() when a handler was just added"
This reverts commit 720faa4df1.
2015-04-20 09:10:29 +02:00
Norman Maurer
a123c495e1 Revert "Add another test case for channelReadComplete() suppression"
This reverts commit daa04cb4f1.
2015-04-20 09:10:14 +02:00
Norman Maurer
b4b14ea19f Ensure backward-compability with 4.0
Motivation:

Each different *ChannelOption did extend ChannelOption in 4.0, which we changed in 4.1. This is a breaking change in terms of the API so we need to ensure we keep the old hierarchy.

Modifications:

- Let all *ChannelOption extend ChannelOption
- Add back constructor and mark it as @deprecated

Result:

No API breakage between 4.0 and 4.1
2015-04-19 13:25:42 +02:00
Pierre DAL-PRA
2ebf07e622 Small typos fixes in Channel's Javadoc 2015-03-21 16:10:24 +01:00
Wouter
baa5990e34 Fix typo in javadoc 2015-03-18 17:15:17 +01:00
Trustin Lee
068132f1ea Fix SocketException in NioSocketChannelUnsafe.closeExecutor()
Related: #3464

Motivation:

When a connection attempt is failed,
NioSocketChannelUnsafe.closeExecutor() triggers a SocketException,
suppressing the channelUnregistered() event.

Modification:

Do not attempt to get SO_LINGER value when a socket is not open yet.

Result:

One less bug
2015-03-05 15:18:10 +09:00
Norman Maurer
fce0989844 [maven-release-plugin] prepare for next development iteration 2015-03-03 02:06:47 -05:00
Norman Maurer
ca3b1bc4b7 [maven-release-plugin] prepare release netty-4.1.0.Beta4 2015-03-03 02:05:52 -05:00
jongyoon lim
e3edec25c5 typo_fix in the comment 2015-02-25 20:30:40 +01:00
Norman Maurer
a709553819 Allow to use EmbeddedChannel.schedule*(...)
Motivation:

At the moment when EmbeddedChannel is used and a ChannelHandler tries to schedule and task it will throw an UnsupportedOperationException. This makes it impossible to test these handlers or even reuse them with EmbeddedChannel.

Modifications:

- Factor out reusable scheduling code into AbstractSchedulingEventExecutor
- Let EmbeddedEventLoop and SingleThreadEventExecutor extend AbstractSchedulingEventExecutor
- add EmbbededChannel.runScheduledPendingTasks() which allows to run all scheduled tasks that are ready

Result:

Embeddedchannel is now usable even with ChannelHandler that try to schedule tasks.
2015-02-20 11:57:32 +01:00
jongyoon lim
1e09409604 removed an unnecessary local variable for consistency 2015-02-18 20:10:42 +01:00
Norman Maurer
99bd43ed51 Allow to get existing ChannelOption / AttributeKey from String
Motivation:

We should allow to get a ChannelOption/AttributeKey from a String. This will make it a lot easier to make use of configuration files in applications.

Modifications:

- Add exists(...), newInstance(...) method to ChannelOption and AttributeKey and alter valueOf(...) to return an existing instance for a String or create one.
- Add unit tests.

Result:

Much more flexible usage of ChannelOption and AttributeKey.
2015-02-18 09:29:37 +01:00
Norman Maurer
6e508e60e7 Move generic unix classes/interfaces out of epoll package
Motivation:

As we plan to have other native transports soon (like a kqueue transport) we should move unix classes/interfaces out of the epoll package so we
introduce other implementations without breaking stuff before the next stable release.

Modifications:

Create a new io.netty.channel.unix package and move stuff over there.

Result:

Possible to introduce other native impls beside epoll.
2015-02-17 17:56:01 +01:00
Cristian
4b83eee133 Fixed ServerBootstrap#group(EventLoopGroup, EventLoopGroup) javadoc 2015-02-16 11:21:50 +01:00
Trustin Lee
daa04cb4f1 Add another test case for channelReadComplete() suppression
Related commit:
- a41b46ff43

Motivation:

We need a test case for the commit above.
2015-02-09 16:29:21 +09:00
Norman Maurer
a69fbaeed9 Not execute shutdownOutput(...) and close(...) in the EventLoop if SO_LINGER is used.
Motivation:

If SO_LINGER is used shutdownOutput() and close() syscalls will block until either all data was send or until the timeout exceed. This is a problem when we try to execute them on the EventLoop as this means the EventLoop may be blocked and so can not process any other I/O.

Modifications:

- Add AbstractUnsafe.closeExecutor() which returns null by default and use this Executor for close if not null.
- Override the closeExecutor() in NioSocketChannel and EpollSocketChannel and return GlobalEventExecutor.INSTANCE if getSoLinger() > 0
- use closeExecutor() in shutdownInput(...) in NioSocketChannel and EpollSocketChannel

 Result:

No more blocking of the EventLoop if SO_LINGER is used and shutdownOutput() or close() is called.
2015-02-08 20:15:47 +01:00
Trustin Lee
a1efd1871b Reorder PlatformDependent.isRoot() check
Motivation:

isRoot() is an expensive operation. We should avoid calling it if
possible.

Modifications:

Move the isRoot() checks to the end of the 'if' block, so that isRoot()
is evaluated only when really necessary.

Result:

isRoot() is evaluated only when SO_BROADCAST is set and the bind address
is anylocal address.
2015-02-08 12:00:16 +09:00
Trustin Lee
720faa4df1 Do not suppress channelReadComplete() when a handler was just added
Related:
- 27a25e29f7

Motivation:

The commit mentioned above introduced a regression where
channelReadComplete() event is swallowed by a handler which was added
dynamically.

Modifications:

Do not suppress channelReadComplete() if the current handler's
channelRead() method was not invoked at all, so that a just-added
handler does not suppress channelReadComplete().

Result:

Regression is gone, and channelReadComplete() is invoked when necessary.
2015-02-07 23:09:07 +09:00
Trustin Lee
27a25e29f7 Ensure channelReadComplete() is called only when necessary
Motivation:

Even if a handler called ctx.fireChannelReadComplete(), the next handler
should not get its channelReadComplete() invoked if fireChannelRead()
was not invoked before.

Modifications:

- Ensure channelReadComplete() is invoked only when the handler of the
  current context actually produced a message, because otherwise there's
  no point of triggering channelReadComplete().
  i.e. channelReadComplete() must follow channelRead().
- Fix a bug where ctx.read() was not called if the handler of the
  current context did not produce any message, making the connection
  stall. Read the new comment for more information.

Result:

- channelReadComplete() is invoked only when it makes sense.
- No stale connection
2015-02-07 16:13:56 +09:00
Norman Maurer
abf7afca76 [#3367] Fix re-entrance bug in PendingWriteQueue
Motivation:

Because of a re-entrance bug in PendingWriteQueue it was possible to get the queue corrupted and also trigger an IllegalStateException caused by multiple recycling of the internal PendingWrite objects.

Modifications:

- Correctly guard against re-entrance

Result:

No more IllegalStateException possible
2015-02-06 19:49:34 +01:00
Norman Maurer
3030b4afe3 Allow to recv and send file descriptors when using EpollDomainSocketChannel.
Motiviation:

When using domain sockets on linux it is supported to recv and send file descriptors. This can be used to pass around for example sockets.

Modifications:
- Add support for recv and send file descriptors when using EpollDomainSocketChannel.
- Allow to obtain the file descriptor for an Epoll*Channel so it can be send via domain sockets.

Result:
recv and send of file descriptors is supported now.
2015-02-04 20:07:43 +01:00
Marco Craveiro
6d07264412 Minor idiomatic changes to java docs 2015-02-04 08:28:29 +01:00
haohao
4bafb4f95b [#3368] Ensure ByteBuf is not release two times
Motivation:

As the ByteBuf is not set to null after release it we may try to release it again in handleReadException()

Modifications:

-  set ByteBuf to null to avoid another byteBuf.release() to be called in handleReadException()

Result:

No IllegalReferenceCountException anymore
2015-01-29 18:26:08 +01:00
ysammy
0bc0851569 Fix documentation for ChannelHandlerContext#fireChannelReadComplete
Motivation:
Fix a minor documentation bug in
ChannelHandlerContext#fireChannelReadComplete.

Modifications:
ChannelHandlerContext#fireChannelReadComplete no longer references an
incorrect method in its javadoc.

Results:
Documentation is correct.
2014-12-12 18:43:06 +01:00
Norman Maurer
12c9ce7f67 Allow to lazy create a DefaultFileRegion from a File
Motivation:

We only provided a constructor in DefaultFileRegion that takes a FileChannel which means the File itself needs to get opened on construction. This has the problem that if you want to write a lot of Files very fast you may end up with may open FD's even if they are not needed yet. This can lead to hit the open FD limit of the OS.

Modifications:

Add a new constructor to DefaultFileRegion which allows to construct it from a File. The FileChannel will only be obtained when transferTo(...) is called or the DefaultFileRegion is explicit open'ed via open() (this is needed for the native epoll transport)

Result:

Less resource usage when writing a lot of DefaultFileRegion.
2014-12-11 12:04:17 +01:00
Trustin Lee
298e7af647 Trigger channelWritabilityChanged() later to avoid reentrance
Related: #3212

Motivation:

When SslHandler and ChunkedWriteHandler exists in a pipeline together,
it is possible that ChunkedWriteHandler.channelWritabilityChanged()
invokes SslHandler.flush() and vice versa. Because they can feed each
other (i.e. ChunkedWriteHandler.channelWritabilityChanged() ->
SslHandler.flush() -> ChunkedWriteHandler.channelWritabilityChanged() ->
..), they can fall into an inconsistent state due to reentrance (e.g.
bad MAC record at the remote peer due to incorrect ordering.)

Modifications:

- Trigger channelWritabilityChanged() using EventLoop.execute() when
  there's a chance where channelWritabilityChanged() can cause a
  reentrance issue
- Fix test failures caused by the modification

Result:

Fix the handler reentrance issues related with a
channelWritabilityChanged() event
2014-12-10 18:40:26 +09:00
Trustin Lee
3957a88a94 Make PendingWriteQueue.recycle() update its state before triggering an event
Related: #3212

Motivation:

PendingWriteQueue.recycle() updates its data structure after triggering
a channelWritabilityChanged() event. It causes a rare corruption such as
double free when channelWritabilityChanged() method accesses the
PendingWriteQueue.

Modifications:

Update the state of PendingWriteQueue before triggering an event.

Result:

Fix a rare double-free problem
2014-12-07 23:27:33 +09:00
Trustin Lee
1ef6f14734 Trigger exceptionCaught() when VoidChannelPromise fails
Related: #3190

Motivation:

When an outbound handler method raises an exception, its promise is
marked as failed.  If the promise is done already, the exception is
logged.

When the promise is void, exceptionCaught() must be triggered to notify
a user. However, ChannelHandlerInvokerUtil simply swallows it.

Modifications:

Do not swallow an exception when the promise is void.

Result:

A user who uses a void promise for an outbound operation will be
notified on failure.
2014-12-07 16:06:55 +09:00
Trustin Lee
3dbca4a9e2 Fire channelRead() event immediately in OIO message channels
Related: #3189

Motivation:

OIO transport implementations block for at most 1 second to wait for
additional messages (or accepted connections).

However, because AbstractOioMessageChannel defers the channelRead()
events for the messages read so far until there's nothing to read up to
maxMessagesPerRead, any read operation will be followed by a 1-second
delay.

Modifications:

Fire channelRead() events as soon as doRead() returns so that there is
no 1 second delay between the actual read and the channelRead() event.

Result:

No more weird 1-second delay
2014-12-07 12:13:26 +09:00
Trustin Lee
46576fd2ff Fix a race condition where handler is removed before unregistration
Related: #3156

Motivation:

Let's say we have a channel with the following pipeline configuration:

  HEAD --> [E1] H1 --> [E2] H2 --> TAIL

when the channel is deregistered, the channelUnregistered() methods of
H1 and H2 will be invoked from the executor thread of E1 and E2
respectively. To ensure that the channelUnregistered() methods are
invoked from the correct thread, new one-time tasks will be created
accordingly and be scheduled via Executor.execute(Runnable).

As soon as the one-time tasks are scheduled,
DefaultChannelPipeline.fireChannelUnregistered() will start to remove
all handlers from the pipeline via teardownAll(). This process is
performed in reversed order of event propagation. i.e. H2 is removed
first, and then H1 is removed.

If the channelUnregistered() event has been passed to H2 before H2 is
removed, a user does not see any problem.

If H2 has been removed before channelUnregistered() event is passed to
H2, a user will often see the following confusing warning message:

  An exceptionCaught() event was fired, and it reached at the tail of
  the pipeline. It usually means the last handler in the pipeline did
  not handle the exception.

Modifications:

To ensure that the handlers are removed *after* all events are
propagated, traverse the pipeline in ascending order before performing
the actual removal.

Result:

A user does not get the confusing warning message anymore.
2014-12-05 16:09:00 +09:00
Trustin Lee
46ef370ee1 Copy the resolver configuration when cloning Bootstrap
Motivation:

Bootstrap.clone() does not copy the resolver configuration.

Modifications:

Copy the resolver configuration when cloning.

Result:

Bug fixed
2014-12-01 19:50:12 +09:00
Frank Barber
f4d3f81d6c Prevent channel re-registration from firing channelActive
Motivation:

AbstractUnsafe considers two possibilities during channel registration. First,
the channel may be an outgoing connection, in which case it will be registered
before becoming active. Second, the channel may be an incoming connection in,
which case the channel will already be active when it is registered. To handle
the second case, AbstractUnsafe checks if the channel is active after
registration and calls ChannelPipeline.fireChannelActive() if so.  However, if
an active channel is deregistered and then re-registered this logic causes a
second fireChannelActive() to be invoked. This is unexpected; it is reasonable
for handlers to assume that this method will only be invoked once per channel.

Modifications:

This change introduces a flag into AbstractUnsafe to recognize if this is the
first or a subsequent registration. ChannelPipeline.fireChannelActive() is only
possible for the first registration.

Result:

ChannelPipeline.fireChannelActive() is only called once.
2014-11-30 19:51:30 +01:00
Ronald Chen
e1273147fa replaced broken &lt with < and same for gt 2014-11-29 19:33:50 +01:00
Idel Pivnitskiy
35db3c6710 Small performance improvements
Motivation:

Found performance issues via FindBugs and PMD.

Modifications:

- Removed unnecessary boxing/unboxing operations in DefaultTextHeaders.convertToInt(CharSequence) and DefaultTextHeaders.convertToLong(CharSequence). A boxed primitive is created from a string, just to extract the unboxed primitive value.
- Added a static modifier for DefaultHttp2Connection.ParentChangedEvent class. This class is an inner class, but does not use its embedded reference to the object which created it. This reference makes the instances of the class larger, and may keep the reference to the creator object alive longer than necessary.
- Added a static compiled Pattern to avoid compile it each time it is used when we need to replace some part of authority.
- Improved using of StringBuilders.

Result:

Performance improvements.
2014-11-20 00:10:06 -05:00
Sam Young
9ba3126bd4 Add generic versions of PromiseAggregator and PromiseNotifier.
Motivation:

ChannelPromiseAggregator and ChannelPromiseNotifiers only allow
consumers to work with Channels as the result type. Generic versions
of these classes allow consumers to aggregate or broadcast the results
of an asynchronous execution with other result types.

Modifications:

Add PromiseAggregator and PromiseNotifier. Add unit tests for both.
Remove code in ChannelPromiseAggregator and ChannelPromiseNotifier and
modify them to extend the new base classes.

Result:

Consumers can now aggregate or broadcast the results of an asynchronous
execution with results types other than Channel.
2014-11-07 09:06:58 +01:00
Trustin Lee
9826d9bc1a Fix compilation errors in ChannelOutboundBufferTest 2014-10-25 16:57:22 +09:00
Trustin Lee
d59629377c Implement user-defined writability flags
Related: #2945

Motivation:

Some special handlers such as TrafficShapingHandler need to override the
writability of a Channel to throttle the outbound traffic.

Modifications:

Add a new indexed property called 'user-defined writability flag' to
ChannelOutboundBuffer so that a handler can override the writability of
a Channel easily.

Result:

A handler can override the writability of a Channel using an unsafe API.
For example:

  Channel ch = ...;
  ch.unsafe().outboundBuffer().setUserDefinedWritability(1, false);
2014-10-25 15:59:13 +09:00
Trustin Lee
7ddc8a445c Make Bootstrap and ServerBootstrap fully overridable
Related: #2034

Motivation:

Some users want to mock Bootstrap (or ServerBootstrap), and thus they
should not be final but be fully overridable and extensible.

Modifications:

Remove finals wherever possible

Result:

@daschl is happy.
2014-10-17 16:17:42 +09:00
Trustin Lee
f3a2c22738 Fix an infinite loop when writing a zero-length FileRegion
Related: #2964

Motivation:

Writing a zero-length FileRegion to an NIO channel will lead to an
infinite loop.

Modification:

- Do not write a zero-length FileRegion by protecting with proper 'if'.
- Update the testsuite

Result:

Another bug fixed
2014-10-17 16:06:51 +09:00
Trustin Lee
e848066cab Name resolver API and DNS-based name resolver
Motivation:

So far, we relied on the domain name resolution mechanism provided by
JDK.  It served its purpose very well, but had the following
shortcomings:

- Domain name resolution is performed in a blocking manner.
  This becomes a problem when a user has to connect to thousands of
  different hosts. e.g. web crawlers
- It is impossible to employ an alternative cache/retry policy.
  e.g. lower/upper bound in TTL, round-robin
- It is impossible to employ an alternative name resolution mechanism.
  e.g. Zookeeper-based name resolver

Modification:

- Add the resolver API in the new module: netty-resolver
- Implement the DNS-based resolver: netty-resolver-dns
  .. which uses netty-codec-dns
- Make ChannelFactory reusable because it's now used by
  io.netty.bootstrap, io.netty.resolver.dns, and potentially by other
  modules in the future
  - Move ChannelFactory from io.netty.bootstrap to io.netty.channel
  - Deprecate the old ChannelFactory
  - Add ReflectiveChannelFactory

Result:

It is trivial to resolve a large number of domain names asynchronously.
2014-10-16 17:05:20 +09:00
Trustin Lee
87c82d4845 Do not consider PortUnreachableException to require channel closure
Motivation:

When a datagram packet is sent to a destination where nobody actually listens to,
the server O/S will respond with an ICMP Port Unreachable packet.
The ICMP Port Unreachable packet is translated into PortUnreachableException by JDK.
PortUnreachableException is not a harmful exception that prevents a user from sending a datagram.
Therefore, we should not close a datagram channel when PortUnreachableException is caught.

Modifications:

- Do not close a channel when the caught exception is PortUnreachableException.

Result:

A datagram channel is not closed unexpectedly anymore.
2014-10-16 17:04:25 +09:00
Trustin Lee
f8349f8dc5 Add AbstractUnsafe.annotateConnectException()
Motivation:

JDK's exception messages triggered by a connection attempt failure do
not contain the related remote address in its message.  We currently
append the remote address to ConnectException's message, but I found
that we need to cover more exception types such as SocketException.

Modifications:

- Add AbstractUnsafe.annotateConnectException() to de-duplicate the
  code that appends the remote address

Result:

- Less duplication
- A transport implementor can annotate connection attempt failure
  message more easily
2014-10-14 12:29:08 +09:00
Trustin Lee
fe05b6e514 Auto-generate the handler name when null is specified as a name
Motivation:

There's no way to generate the name of a handler being newly added
automatically and reliably.

For example, let's say you have a routine that adds a set of handlers to
a pipeline using addBefore() or addAfter().  Because addBefore() and
addAfter() always require non-conflicting non-null handler name, making
the multiple invocation of the routine on the same pipeline is
non-trivial.

Modifications:

- If a user specifies null as the name of the new handler,
  DefaultChannelPipeline generates one.
- Update the documentation of ChannelPipeline to match the new behavior

Result:

A user doesn't need to worry about name conflicts anymore.
2014-10-14 12:29:08 +09:00
Luke Wood
a64484249c Access autoRead via an AtomicIntegerFieldUpdater.
Motiviation:

Before this change, autoRead was a volatile boolean accessed directly.  Any thread that invoked the DefaultChannelConfig#setAutoRead(boolean) method would read the current value of autoRead, and then set a new value.  If the old value did not match the new value, some action would be immediately taken as part of the same method call.

As volatile only provides happens-before consistency, there was no guarantee that the calling thread was actually the thread mutating the state of the autoRead variable (such that it should be the one to invoke the follow-up actions).  For example, with 3 threads:
 * Thread 1: get = false
 * Thread 1: set = true
 * Thread 1: invokes read()
 * Thread 2: get = true
 * Thread 3: get = true
 * Thread 2: set = false
 * Thread 2: invokes autoReadCleared()
 * Event Loop receives notification from the Selector that data is available, but as autoRead has been cleared, cancels the operation and removes read interest
 * Thread 3: set = true

This results in a livelock - autoRead is set true, but no reads will happen even if data is available (as readyOps).  The only way around this livelock currently is to set autoRead to false, and then back to true.

Modifications:

Write access to the autoRead variable is now made using the getAndSet() method of an AtomicIntegerFieldUpdater, AUTOREAD_UPDATER.  This also changed the type of the underlying autoRead variable to be an integer, as no AtomicBooleanFieldUpdater class exists.  Boolean logic is retained by assuming that 1 is true and 0 is false.

Result:

There is no longer a race condition between retrieving the old value of the autoRead variable and setting a new value.
2014-10-13 15:15:58 +02:00
Norman Maurer
246b65c6b6 [#2586] Use correct EventExecutor to notify for bind failures on late registration
Motivation:

We used the wrong EventExecutor to notify for bind failures if a late registration was done.

Modifications:

Use the correct EventExecutor to notify and only use the GlobelEventExecutor if the registration fails itself.

Result:

The correct Thread will do the notification.
2014-08-20 16:34:57 +02:00
Trustin Lee
b5f61d0de5 [maven-release-plugin] prepare for next development iteration 2014-08-16 03:27:42 +09:00
Trustin Lee
76ac3b21a5 [maven-release-plugin] prepare release netty-4.1.0.Beta3 2014-08-16 03:27:37 +09:00
Trustin Lee
02643e41fb Fix a bug where ChannelOutboundBuffer.removeBytes() throws ClassCastException
When a ChannelOutboundBuffer contains ByteBufs followed by a FileRegion,
removeBytes() will fail with a ClassCastException.  It should break the
loop instead.
2014-08-15 09:57:04 -07:00
Trustin Lee
9ee51fc4c7 Fix the regression caused by f31c630c8c
f31c630c8c was causing
SocketGatheringWriteTest to fail because it does not take the case where
an empty buffer exists in a gathering write.

When there is an empty buffer in a gathering write, the number of
buffers returned by ChannelOutboundBuffer.nioBuffer() and the actual
number of write attemps can differ.

To remove the write requests correctly, a byte transport must use
ChannelOutboundBuffer.removeBytes()
2014-08-15 09:43:56 -07:00
Norman Maurer
9b99ac0bcb [#2771] Correctly handle constructing of EmbeddedChannel
Motivation:

Because of an incorrect logic in teh EmbeddedChannel constructor it is not possible to use EmbeddedChannel with a ChannelInitializer as constructor argument. This is because it adds the internal LastInboundHandler to its ChannelPipeline before it register itself to the EventLoop.

Modifications:

First register self to EventLoop before add LastInboundHandler to the ChannelPipeline.

Result:

It's now possible to use EmbeddedChannel with ChannelInitializer.
2014-08-15 12:21:37 +02:00
Norman Maurer
dcfdad9e9e [#2769] Fix regression when writing different message types
Motivation:

Due a regression NioSocketChannel.doWrite(...) will throw a ClassCastException if you do something like:

channel.write(bytebuf);
channel.write(fileregion);
channel.flush();

Modifications:

Correctly handle writing of different message types by using the correct message count while loop over them.

Result:

No more ClassCastException
2014-08-15 11:56:12 +02:00
Trustin Lee
b3c1904cc9 [maven-release-plugin] prepare for next development iteration 2014-08-15 09:31:03 +09:00
Trustin Lee
e013b2400f [maven-release-plugin] prepare release netty-4.1.0.Beta2 2014-08-15 09:30:59 +09:00
Norman Maurer
0eac4fce29 Revert "[#2761] ChannelOutboundBuffer can cause data-corruption because of caching ByteBuffers"
This reverts commit 536141ba69.
2014-08-13 21:47:00 +02:00
Norman Maurer
a7d1f983a2 [#2761] Proper work-around for data-corruption caused by cached ByteBuffers
Motivation:

The previous fix did disable the caching of ByteBuffers completely which can cause performance regressions. This fix makes sure we use nioBuffers() for all writes in NioSocketChannel and so prevent data-corruptions. This is still kind of a workaround which will be replaced by a more fundamental fix later.

Modifications:

- Revert 4059c9f354
- Use nioBuffers() for all writes to prevent data-corruption

Result:

No more data-corruption but still retain the original speed.
2014-08-13 21:24:44 +02:00
Norman Maurer
f89907dba5 Revert "[#2762] Not expand ByteBuffer[] in ChannelOutboundBuffer"
This reverts commit de3c0507c1 as it may cause problem if a CompositeByteBuf has more then 1024 components.
2014-08-13 16:40:34 +02:00
Norman Maurer
de3c0507c1 [#2762] Not expand ByteBuffer[] in ChannelOutboundBuffer
Motivation:

At the moment we expand the ByteBuffer[] when we have more then 1024 ByteBuffer to write and replace the stored instance in its FastThreadLocal. This is not needed and may even harm performance on linux as IOV_MAX is 1024 and so this may cause the JVM to do an array copy.

Modifications:

Just exit the nioBuffers() method if we can not fit more ByteBuffer in the array. This way we will pick them up on the next call.

Result:

Remove uncessary array copy and simplify the code.
2014-08-13 11:59:12 +02:00
Norman Maurer
536141ba69 [#2761] ChannelOutboundBuffer can cause data-corruption because of caching ByteBuffers
Motivation:

We cache the ByteBuffers in ChannelOutboundBuffer.nioBuffers() for the Entries in the ChannelOutboundBuffer to reduce some overhead. The problem is this can lead to data-corruption if an incomplete write happens and next time we try to do a non-gathering write.

To fix this we should remove the caching which does not help a lot anyway and just make the code buggy.

Modifications:

Remove the caching of ByteBuffers.

Result:

No more data-corruption.
2014-08-13 11:16:02 +02:00
Norman Maurer
286b89933c Allow to obtain RecvByteBufAllocator.Handle to allow more flexible implementations
Motivation:

At the moment it's only possible for a user to set the RecvByteBufAllocator for a Channel but not access the Handle once it is assigned. This makes it hard to write more flexible implementations.

Modifications:

Add a new method to the Channel.Unsafe to allow access the the used Handle for the Channel. The RecvByteBufAllocator.Handle is created lazily.

Result:

It's possible to write more flexible implementatons that allow to adjust stuff on the fly for a Handle that is used by a Channel
2014-08-12 06:53:57 +02:00
Norman Maurer
02e7e53cbb [#2752] Add PendingWriteQueue for queue up writes
Motivation:

Sometimes ChannelHandler need to queue writes to some point and then process these. We currently have no datastructure for this so the user will use an Queue or something like this. The problem is with this Channel.isWritable() will not work as expected and so the user risk to write to fast. That's exactly what happened in our SslHandler. For this purpose we need to add a special datastructure which will also take care of update the Channel and so be sure that Channel.isWritable() works as expected.

Modifications:

- Add PendingWriteQueue which can be used for this purpose
- Make use of PendingWriteQueue in SslHandler

Result:

It is now possible to queue writes in a ChannelHandler and still have Channel.isWritable() working as expected. This also fixes #2752.
2014-08-12 06:38:22 +02:00
Norman Maurer
869687bd71 Port ChannelOutboundBuffer and related changes from 4.0
Motivation:

We did various changes related to the ChannelOutboundBuffer in 4.0 branch. This commit port all of them over and so make sure our branches are synced in terms of these changes.

Related to [#2734], [#2709], [#2729], [#2710] and [#2693] .

Modification:
Port all changes that was done on the ChannelOutboundBuffer.

This includes the port of the following commits:
 - 73dfd7c01b
 - 997d8c32d2
 - e282e504f1
 - 5e5d1a58fd
 - 8ee3575e72
 - d6f0d12a86
 - 16e50765d1
 - 3f3e66c31a

Result:
 - Less memory usage by ChannelOutboundBuffer
 - Same code as in 4.0 branch
 - Make it possible to use ChannelOutboundBuffer with Channel implementation that not extends AbstractChannel
2014-08-05 15:00:45 +02:00
Norman Maurer
750eed1804 Fix broken test after change the maximal value of the pid. Part of [#2706] 2014-07-28 10:39:44 -07:00
Norman Maurer
168e2dde05 [#2706] Allow pid up to 4194304
Motivation:

The PID_MAX_LIMIT on 64bit linux systems is 4194304 and on osx it is 99998. At the moment we use 65535 as an upper-limit which is too small.

Modifications:

Use 4194304 as max possible value

Result:

No more false-positives when try to detect current pid.
2014-07-28 10:12:49 -07:00
Norman Maurer
f88cd62354 [#2692] Allows notify ChannelFutureProgressListener on complete writes
Motivation:

We have some inconsistency when handling writes. Sometimes we call ChannelOutboundBuffer.progress(...) also for complete writes and sometimes not. We should call it always.

Modifications:

Correctly call ChannelOuboundBuffer.progress(...) for complete and incomplete writes.

Result:

Consistent behavior
2014-07-28 04:19:23 -07:00
Norman Maurer
88bd6e7a93 Optimize native transport for gathering writes
Motivation:

While benchmarking the native transport with gathering writes I noticed that it is quite slow. This is due the fact that we need to do a lot of array copies to get the buffers into the iov array.

Modification:

Introduce a new class calles IovArray which allows to fill buffers directly in a iov array that can be passed over to JNI without any array copies. This gives a nice optimization in terms of speed when doing gathering writes.

Result:

Big performance improvement when doing gathering writes. See the included benchmark...

Before:
[nmaurer@xxx]~% wrk/wrk -H 'Host: localhost' -H 'Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8' -H 'Connection: keep-alive' -d 120 -c 256 -t 16 --pipeline 256  http://xxx:8080/plaintext
Running 2m test @ http://xxx:8080/plaintext
  16 threads and 256 connections
  Thread Stats   Avg      Stdev     Max   +/- Stdev
    Latency    23.44ms   16.37ms 259.57ms   91.77%
    Req/Sec   181.99k    31.69k  304.60k    78.12%
  346544071 requests in 2.00m, 46.48GB read
Requests/sec: 2887885.09
Transfer/sec:    396.59MB

With this change:
[nmaurer@xxx]~% wrk/wrk -H 'Host: localhost' -H 'Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8' -H 'Connection: keep-alive' -d 120 -c 256 -t 16 --pipeline 256  http://xxx:8080/plaintext
Running 2m test @ http://xxx:8080/plaintext
  16 threads and 256 connections
  Thread Stats   Avg      Stdev     Max   +/- Stdev
    Latency    21.93ms   16.33ms 305.73ms   92.34%
    Req/Sec   194.56k    33.75k  309.33k    77.04%
  369617503 requests in 2.00m, 49.57GB read
Requests/sec: 3080169.65
Transfer/sec:    423.00MB
2014-07-25 09:55:02 +02:00
Willem Jiang
b029800b68 Updated the ChannelGroup JavaDoc by removing b.releaseExternalResources(); 2014-07-24 10:55:09 +02:00
Trustin Lee
830091c260 Reduce the default initial capacity of ChannelOutboundBuffer
Motivation:

ChannelOutboundBuffer is basically a circular array queue of its entry
objects.  Once an entry is created in the array, it is never nulled out
to reduce the allocation cost.

However, because it is a circular queue, the array almost always ends up
with as many entry instances as the size of the array, regardless of the
number of pending writes.

At worst case, a channel might have only 1 pending writes at maximum
while creating 32 entry objects, where 32 is the initial capacity of the
array.

Modifications:

- Reduce the initial capacity of the circular array queue to 4.
- Make the initial capacity of the circular array queue configurable

Result:

We spend 4 times less memory for entry objects under certain
circumstances.
2014-07-22 13:32:25 -07:00
Norman Maurer
faf9ac9a30 [#2680] NioSocketChannelOutboundBuffer.nioBuffers() / EpollSocketChannelOutboundBuffer.memoryAddresses() should always return non-null array as stated in javadocs
Motivation:

At the moment NioSocketChannelOutboundBuffer.nioBuffers() / EpollSocketChannelOutboundBuffer.memoryAddresses() returns null if something is contained in the ChannelOutboundBuffer which is not a ByteBuf. This is a problem for two reasons:
  1 - In the javadocs we state that it will never return null
  2 - We may do a not optimal write as there may be things that could be written via gathering writes

Modifications:

Change NioSocketChannelOutboundBuffer.nioBuffers() /  EpollSocketChannelOutboundBuffer.memoryAddresses() to never return null but have it contain all ByteBuffer that were found before the non ByteBuf. This way we can do a gathering write and also conform to the javadocs.

Result:

Better speed and also correct implementation in terms of the api.
2014-07-20 19:57:01 +02:00
Idel Pivnitskiy
b83df4c6b3 Fix NPE problems
Motivation:

Now Netty has a few problems with null values.

Modifications:

- Check HAProxyProxiedProtocol in HAProxyMessage constructor and throw NPE if it is null.
If HAProxyProxiedProtocol is null we will set AddressFamily as null. So we will get NPE inside checkAddress(String, AddressFamily) and it won't be easy to understand why addrFamily is null.
- Check File in DiskFileUpload.toString().
If File is null we will get NPE when calling toString() method.
- Check Result<String> in MqttDecoder.decodeConnectionPayload(...).
If !mqttConnectVariableHeader.isWillFlag() || !mqttConnectVariableHeader.hasUserName() || !mqttConnectVariableHeader.hasPassword() we will get NPE when we will try to create new instance of MqttConnectPayload.
- Check Unsafe before calling unsafe.getClass() in PlatformDependent0 static block.
- Removed unnecessary null check in WebSocket08FrameEncoder.encode(...).
Because msg.content() can not return null.
- Removed unnecessary null check in DefaultStompFrame(StompCommand) constructor.
Because we have this check in the super class.
- Removed unnecessary null checks in ConcurrentHashMapV8.removeTreeNode(TreeNode<K,V>).
- Removed unnecessary null check in OioDatagramChannel.doReadMessages(List<Object>).
Because tmpPacket.getSocketAddress() always returns new SocketAddress instance.
- Removed unnecessary null check in OioServerSocketChannel.doReadMessages(List<Object>).
Because socket.accept() always returns new Socket instance.
- Pass Unpooled.buffer(0) instead of null inside CloseWebSocketFrame(boolean, int) constructor.
If we will pass null we will get NPE in super class constructor.
- Added throw new IllegalStateException in GlobalEventExecutor.awaitInactivity(long, TimeUnit) if it will be called before GlobalEventExecutor.execute(Runnable).
Because now we will get NPE. IllegalStateException will be better in this case.
- Fixed null check in OpenSslServerContext.setTicketKeys(byte[]).
Now we throw new NPE if byte[] is not null.

Result:

Added new null checks when it is necessary, removed unnecessary null checks and fixed some NPE problems.
2014-07-20 12:55:22 +02:00
Idel Pivnitskiy
dd429b2495 Small fixes and improvements
Motivation:

Fix some typos in Netty.

Modifications:

- Fix potentially dangerous use of non-short-circuit logic in Recycler.transfer(Stack<?>).
- Removed double 'the the' in javadoc of EmbeddedChannel.
- Write to log an exception message if we can not get SOMAXCONN in the NetUtil's static block.
2014-07-20 09:37:22 +02:00
Norman Maurer
7e61538790 [#2665] Continue writing on IOException when using DatagramChannel
Motivation:

As a DatagramChannel supports to write to multiple remote peers we must not close the Channel once a IOException accours as this error may be only valid for one remote peer.

Modification:

Continue writing on IOException.

Result:

DatagramChannel can be used even after an IOException accours during writing.
2014-07-18 12:49:34 +02:00
Norman Maurer
89593a719b [#2666] Fix possible NPE when try to fullfill connect ChannelPromise
Motivation:

Because of a missing return statement we may produce a NPE when try to fullfill the connect ChannelPromise when it was fullfilled before.

Modification:

Add missing return statement.

Result:

No more NPE.
2014-07-18 07:10:11 +02:00
Trustin Lee
e167b02d52 [maven-release-plugin] prepare for next development iteration 2014-07-04 17:26:02 +09:00
Trustin Lee
ba50cb829b [maven-release-plugin] prepare release netty-4.1.0.Beta1 2014-07-04 17:25:54 +09:00
Trustin Lee
787663a644 [maven-release-plugin] rollback the release of netty-4.1.0.Beta1 2014-07-04 17:11:14 +09:00
Trustin Lee
83eae705e1 [maven-release-plugin] prepare release netty-4.1.0.Beta1 2014-07-04 17:02:17 +09:00
Trustin Lee
5b87cdc8bd Reduce the perceived time taken to retrieve initialSeedUniquifier
Motivation:

When system is in short of entrophy, the initialization of
ThreadLocalRandom can take at most 3 seconds.  The initialization occurs
when ThreadLocalRandom.current() is invoked first time, which might be
much later than the moment when the application has started.  If we
start the initialization of ThreadLocalRandom as early as possible, we
can reduce the perceived time taken for the retrieval.

Modification:

Begin the initialization of ThreadLocalRandom in InternalLoggerFactory,
potentially one of the firstly initialized class in a Netty application.

Make DefaultChannelId retrieve the current process ID before retrieving
the current machine ID, because retrieval of a machine ID is more likely
to use ThreadLocalRandom.current().

Use a dummy channel ID for EmbeddedChannel, which prevents many unit
tests from creating a ThreadLocalRandom instance.

Result:

We gain extra 100ms at minimum for initialSeedUniquifier generation.  If
an application has its own initialization that takes long enough time
and generates good amount of entrophy, it is very likely that we will
gain a lot more.
2014-07-04 16:04:48 +09:00
Norman Maurer
f8c95c3827 [#2586] Use correct EventLoop to notify delayed bind failures
Motivation:

When a bind fails AbstractBootstrap will use the GlobalEventExecutor to notify the ChannelPromise. We should use the EventLoop of the Channel if possible.

Modification:

Use EventLoop of the Channel if possible to use the correct Thread to notify and so guaranteer the right order of events.

Result:

Use the correct EventLoop for notification
2014-07-03 21:31:05 +02:00
Norman Maurer
217fb0de05 [#2618] Introduce ChannelPromise.unvoid() and ChannelFuture.isVoid()
Motivation:

There is no way for a ChannelHandler to check if the passed in ChannelPromise for a write(...) call is a VoidChannelPromise. This is a problem as some handlers need to add listeners to the ChannelPromise which is not possible in the case of a VoidChannelPromise.

Modification:

- Introduce ChannelFuture.isVoid() which will return true if it is not possible to add listeners or wait on the result.
- Add ChannelPromise.unvoid() which allows to create a ChannelFuture out of a void ChannelFuture which supports all the operations.

Result:

It's now easy to write ChannelHandler implementations which also works when a void ChannelPromise is used.
2014-07-03 14:17:12 +02:00
Trustin Lee
d0912f2709 Fix most inspector warnings
Motivation:

It's good to minimize potentially broken windows.

Modifications:

Fix most inspector warnings from our profile
Update IntObjectHashMap

Result:

Cleaner code
2014-07-02 19:55:07 +09:00
Norman Maurer
36b80c25f7 Correctly return from selector loop one a scheduled task is ready for processing
Motivation:

We use the nanoTime of the scheduledTasks to calculate the milli-seconds to wait for a select operation to select something. Once these elapsed we check if there was something selected or some task is ready for processing. Unfortunally we not take into account scheduled tasks here so the selection loop will continue if only scheduled tasks are ready for processing. This will delay the execution of these tasks.

Modification:

- Check if a scheduled task is ready after selecting
- also make a tiny change in NioEventLoop to not trigger a rebuild if nothing was selected because the timeout was reached a few times in a row.

Result:

Execute scheduled tasks on time.
2014-07-02 09:10:37 +02:00
Norman Maurer
2fa0b83e73 Cleanup comment / code 2014-06-27 21:36:52 +02:00
Norman Maurer
8bf8252060 [#2615] Correctly update SelectionKey after selector rebuild
Motivation:

When a select rebuild was triggered the reference to the SelectionKey is not updated in AbstractNioChannel. This will cause a CancelledKeyException later.

Modification:

Correctly update SelectionKey reference after rebuild

Result:

Fix exception
2014-06-27 17:21:34 +02:00
onlychoice
5275f37ffb Fix a typo in comment 2014-06-24 11:01:35 +02:00
Norman Maurer
030bcaae81 Improve performance of Recycler
Motivation:

Recycler is used in many places to reduce GC-pressure but is still not as fast as possible because of the internal datastructures used.

Modification:

 - Rewrite Recycler to use a WeakOrderQueue which makes minimal guaranteer about order and visibility for max performance.
 - Recycling of the same object multiple times without acquire it will fail.
 - Introduce a RecyclableMpscLinkedQueueNode which can be used for MpscLinkedQueueNodes that use Recycler

These changes are based on @belliottsmith 's work that was part of #2504.

Result:

Huge increase in performance.

4.0 branch without this commit:

Benchmark                                                (size)   Mode   Samples        Score  Score error    Units
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    00000  thrpt        20 116026994.130  2763381.305    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    00256  thrpt        20 110823170.627  3007221.464    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    01024  thrpt        20 118290272.413  7143962.304    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    04096  thrpt        20 120560396.523  6483323.228    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    16384  thrpt        20 114726607.428  2960013.108    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    65536  thrpt        20 119385917.899  3172913.684    ops/s
Tests run: 1, Failures: 0, Errors: 0, Skipped: 0, Time elapsed: 297.617 sec - in io.netty.microbench.internal.RecyclableArrayListBenchmark

4.0 branch with this commit:

Benchmark                                                (size)   Mode   Samples        Score  Score error    Units
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    00000  thrpt        20 204158855.315  5031432.145    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    00256  thrpt        20 205179685.861  1934137.841    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    01024  thrpt        20 209906801.437  8007811.254    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    04096  thrpt        20 214288320.053  6413126.689    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    16384  thrpt        20 215940902.649  7837706.133    ops/s
i.n.m.i.RecyclableArrayListBenchmark.recycleSameThread    65536  thrpt        20 211141994.206  5017868.542    ops/s
Tests run: 1, Failures: 0, Errors: 0, Skipped: 0, Time elapsed: 297.648 sec - in io.netty.microbench.internal.RecyclableArrayListBenchmark
2014-06-24 10:47:38 +02:00
Norman Maurer
81e5f1ad46 [#2589] LocalServerChannel.doClose() throws NPE when localAddress == null
Motivation:

LocalServerChannel.doClose() calls LocalChannelRegistry.unregister(localAddress); without check if localAddress is null and so produce a NPE when pass null the used ConcurrentHashMapV8

Modification:
Check for localAddress != null before try to remove it from Map. Also added a unit test which showed the stacktrace of the error.

Result:

No more NPE during doClose().
2014-06-20 20:13:23 +02:00
Norman Maurer
3d3ec4753d [#2586] Use correct EventLoop to notify delayed successful registration
Motivation:

At the moment AbstractBoostrap.bind(...) will always use the GlobalEventExecutor to notify the returned ChannelFuture if the registration is not done yet. This should only be done if the registration fails later. If it completes successful we should just notify with the EventLoop of the Channel.

Modification:

Use EventLoop of the Channel if possible to use the correct Thread to notify and so guaranteer the right order of events.

Result:

Use the correct EventLoop for notification
2014-06-20 16:59:13 +02:00
Trustin Lee
085a61a310 Refactor FastThreadLocal to simplify TLV management
Motivation:

When Netty runs in a managed environment such as web application server,
Netty needs to provide an explicit way to remove the thread-local
variables it created to prevent class loader leaks.

FastThreadLocal uses different execution paths for storing a
thread-local variable depending on the type of the current thread.
It increases the complexity of thread-local removal.

Modifications:

- Moved FastThreadLocal and FastThreadLocalThread out of the internal
  package so that a user can use it.
- FastThreadLocal now keeps track of all thread local variables it has
  initialized, and calling FastThreadLocal.removeAll() will remove all
  thread-local variables of the caller thread.
- Added FastThreadLocal.size() for diagnostics and tests
- Introduce InternalThreadLocalMap which is a mixture of hard-wired
  thread local variable fields and extensible indexed variables
- FastThreadLocal now uses InternalThreadLocalMap to implement a
  thread-local variable.
- Added ThreadDeathWatcher.unwatch() so that PooledByteBufAllocator
  tells it to stop watching when its thread-local cache has been freed
  by FastThreadLocal.removeAll().
- Added FastThreadLocalTest to ensure that removeAll() works
- Added microbenchmark for FastThreadLocal and JDK ThreadLocal
- Upgraded to JMH 0.9

Result:

- A user can remove all thread-local variables Netty created, as long as
  he or she did not exit from the current thread. (Note that there's no
  way to remove a thread-local variable from outside of the thread.)
- FastThreadLocal exposes more useful operations such as isSet() because
  we always implement a thread local variable via InternalThreadLocalMap
  instead of falling back to JDK ThreadLocal.
- FastThreadLocalBenchmark shows that this change improves the
  performance of FastThreadLocal even more.
2014-06-19 21:13:55 +09:00
Norman Maurer
7ee18e92f9 Small improvement in SimpleChannelInboundHandlerAdapter javadoc 2014-06-18 14:49:36 +02:00
Norman Maurer
061cb21689 Make use of AtomicLongFieldUpdater.addAndGet(...) for cleaner code
Motivation:

The code in ChannelOutboundBuffer can be simplified by using AtomicLongFieldUpdater.addAndGet(...)

Modification:

Replace our manual looping with AtomicLongFieldUpdater.addAndGet(...)

Result:

Cleaner code
2014-06-17 20:18:18 +02:00
Norman Maurer
375da788e7 [#2577] ChannelOutboundBuffer.addFlush() unnecessary loop through all entries on multiple calls
Motivation:

If ChannelOutboundBuffer.addFlush() is called multiple times and flushed != unflushed it will still loop through all entries that are not flushed yet even if it is not needed anymore as these were marked uncancellable before.

Modifications:

Check if new messages were added since addFlush() was called and only if this was the case loop through all entries and try to mark the uncancellable.

Result:

Less overhead when ChannelOuboundBuffer.addFlush() is called multiple times without new messages been added.
2014-06-17 09:31:53 +02:00
belliottsmith
2a2a21ec59 Introduce FastThreadLocal which uses an EnumMap and a predefined fixed set of possible thread locals
Motivation:
Provide a faster ThreadLocal implementation

Modification:
Add a "FastThreadLocal" which uses an EnumMap and a predefined fixed set of possible thread locals (all of the static instances created by netty) that is around 10-20% faster than standard ThreadLocal in my benchmarks (and can be seen having an effect in the direct PooledByteBufAllocator benchmark that uses the DEFAULT ByteBufAllocator which uses this FastThreadLocal, as opposed to normal instantiations that do not, and in the new RecyclableArrayList benchmark);

Result:
Improved performance
2014-06-13 10:56:18 +02:00
Norman Maurer
8180f7922f Optimize DefaultChannelPipeline in terms of memory usage and initialization time
Motivation:
Each of DefaultChannelPipeline instance creates an head and tail that wraps a handler. These are used to chain together other DefaultChannelHandlerContext that are created once a new ChannelHandler is added. There are a few things here that can be improved in terms of memory usage and initialization time.

Modification:
- Only generate the name for the tail and head one time as it will never change anyway
- Rename DefaultChannelHandlerContext to AbstractChannelHandlerContext and make it abstract
- Create a new DefaultChannelHandlerContext that is used when a ChannelHandler is added to the DefaultChannelPipeline
- Rename TailHandler to TailContext and HeadHandler to HeadContext and let them extend AbstractChannelHandlerContext. This way we can save 2 object creations per DefaultChannelPipeline

 Result:
- Less memory usage because we have 2 less objects per DefaultChannelPipeline
- Faster creation of DefaultChannelPipeline as we not need to generate the name for the head and tail
2014-06-10 12:18:38 +02:00
Norman Maurer
a79b69adf5 ChannelFlushPromiseNotifier should allow long value for pendingDataSize
Motivation:
At the moment ChannelFlushPromiseNotifier.add(....) takes an int value for pendingDataSize, which may be too small as a user may need to use a long. This can for example be useful when a user writes a FileRegion etc. Beside this the notify* method names are kind of missleading as these should not contain *Future* because it is about ChannelPromises.

Modification:
Add a new add(...) method that takes a long for pendingDataSize and @deprecated the old method. Beside this also @deprecated all *Future* methods and add methods that have *Promise* in the method name to better reflect usage.

Result:
ChannelFlushPromiseNotifier can be used with bigger data.
2014-06-03 17:34:53 +02:00
Korotaev Boris
5b2a01a196 Fix broken CompositeMatcher
Motivation:

ChannelMatchers#CompositeMatcher inverts matches result.

Modifications:

Switched return values.

Result:

ChannelMatchers#CompositeMatcher will return correct results.
2014-06-01 13:13:49 +02:00
Frédéric Brégier
c255f38647 Correction on StringBuilder default init size
Motivation:
The default StringBuilder size is too small (data.length + 4) while it will be 2*data.length (byte to Hex) + 5 "-" char (since 5 peaces appended).

Modification:
Changing initial size to the correct one

Result:
Allocation of the correct final size from the beginning for this StringBuilder.
2014-05-30 07:35:49 +02:00
Trustin Lee
8df9dd7dda Work around the system configuration issue that causes NioSocketChannelTest to fail
Motivation:

On some ill-configured systems, InetAddress.getLocalHost() fails.  NioSocketChannelTest calls java.net.Socket.connect() and it internally invoked InetAddress.getLocalHost(), which causes the test failures in NioSocketChannelTes on such an ill-configured system.

Modifications:

Use NetUtil.LOCALHOST explicitly.

Result:

NioSocketChannelTest should not fail anymore.
2014-05-28 09:40:49 +09:00
Norman Maurer
2d9e0f53a5 Better implementation of AttributeMap and also add hasAttr(...). See [#2439]
Motivation:
The old DefaultAttributeMap impl did more synchronization then needed and also did not expose a efficient way to check if an attribute exists with a specific key.

Modifications:
* Rewrite DefaultAttributeMap to not use IdentityHashMap and synchronization on the map directly. The new impl uses a combination of AtomicReferenceArray and synchronization per chain (linked-list). Also access the first Attribute per bucket can be done without any synchronization at all and just uses atomic operations. This should fit for most use-cases pretty weel.
* Add hasAttr(...) implementation

Result:
It's now possible to check for the existence of a attribute without create one. Synchronization is per linked-list and the first entry can even be added via atomic operation.
2014-05-15 06:47:42 +02:00
Norman Maurer
59d92ad6cf [#2485] Use RecvByteBufAllocator for all allocations related to read from Channel
Motivation:
At the moment we sometimes use only RecvByteBufAllocator.guess() to guess the next size and the use the ByteBufAllocator.* directly to allocate the buffer. We should always use RecvByteBufAllocator.allocate(...) all the time as this makes the behavior easier to adjust.

Modifications:
Change the read() implementations to make use of RecvByteBufAllocator.

Result:
Behavior is more consistent.
2014-05-10 15:27:43 +02:00
Norman Maurer
9752f37fa0 [#2454] Correctly return null when DefaultChannelPipeline.firstContext() is called on empty pipeline
Motivation:
DefaultChannelPipeline.firstContext() should return null when the ipeline is empty. This is not the case atm.

Modification:
Fix incorrect check in DefaultChannelPipeline.firstContext() and add unit tests.

Result:
Correctly return null when DefaultChannelPipeline.firstContext() is called on empty pipeline.
2014-05-04 21:13:17 +02:00
Norman Maurer
e8b5f19b82 Not cause busy loop when interrupt Thread of NioEventLoop
Motivation:
Because Thread.currentThread().interrupt() will unblock Selector.select() we need to take special care when check if we need to rebuild the Selector. If the unblock was caused by the interrupt() we will clear it and move on as this is most likely a bug in a custom ChannelHandler or a library the user makes use of.

Modification:
Clear the interrupt state of the Thread if the Selector was unblock because of an interrupt and the returned keys was 0.

Result:
No more busy loop caused by Thread.currentThread().interrupt()
2014-04-28 08:18:57 +02:00
Norman Maurer
d8d822fddd Eliminate unnecessary extra synchronization in DefaultChannelPipeline
Motivation:
At the moment whenever we add/remove a ChannelHandler with an EventExecutorGroup we have two synchronization points in the execution path. One to find the childInvoker and one for add/remove itself. We can eliminate the former by call findIInvoker in the synchronization block, as we need to synchronize anyway.

Modification:
Remove the usage of AtomicFieldUpdater and the extra synchronization in findInvoker by moving the call of the method in the synchronized(this) block.

Result:
Less synchronization points and volatile reads/writes
2014-04-25 14:15:23 +02:00
Trustin Lee
0fceef8ab6 Undeprecate deregister() and chanelUnregistered()
Motivation:

As discussed in #2250, it will become much less complicated to implement
deregistration and reregistration of a channel once #2250 is resolved.
Therefore, there's no need to deprecate deregister() and
channelUnregistered().

Modification:

- Undeprecate deregister() and channelUnregistered()
- Remove SuppressWarnings annotations where applicable

Result:

We (including @jakobbuchgraber) are now ready to play with #2250 at
master
2014-04-25 16:40:42 +09:00
Trustin Lee
d765f6b870 Synchronized between 4.1 and master (part 3)
Motivation:

4 and 5 were diverged long time ago and we recently reverted some of the
early commits in master.  We must make sure 4.1 and master are not very
different now.

Modification:

Fix found differences

Result:

4.1 and master got closer.
2014-04-25 16:17:59 +09:00
Trustin Lee
b9039eaa82 Synchronized between 4.1 and master again (part 2)
Motivation:
4 and 5 were diverged long time ago and we recently reverted some of the
early commits in master.  We must make sure 4.1 and master are not very
different now.

Modification:
Remove ChannelHandlerInvoker.writeAndFlush(...) and the related
implementations.

Result:
4.1 and master got closer.
2014-04-25 15:06:26 +09:00
Norman Maurer
8c3eaf3b56 Synchronized between 4.1 and master again
Motivation:
4 and 5 were diverged long time ago and we recently reverted some of the
early commits in master.  We must make sure 4.1 and master are not very
different now.

Modification:
Remove ChannelHandlerInvoker.writeAndFlush(...) and the related implementations.

Result:
4.1 and master got closer.
2014-04-24 21:28:24 +02:00
Norman Maurer
a2f1f21612 Synchronized between 4.1 and master
Motivation:

4 and 5 were diverged long time ago and we recently reverted some of the
early commits in master.  We must make sure 4.1 and master are not very
different now.

Modification:

Small adjustments to match up branches

Result:

4.1 and master got closer.
2014-04-24 21:04:20 +02:00
Trustin Lee
db3709e652 Synchronized between 4.1 and master
Motivation:

4 and 5 were diverged long time ago and we recently reverted some of the
early commits in master.  We must make sure 4.1 and master are not very
different now.

Modification:

Fix found differences

Result:

4.1 and master got closer.
2014-04-25 00:38:02 +09:00
Norman Maurer
81b0e2af02 Make NioSocketChannelTest more bullet-proof
Motivation:
I had the NioSocketChannelTest.testFlushCloseReentrance() fail sometimes on one of my linux installation. This change let it pass all the time.

Modification:
Set the SO_SNDBUF to a small value to force split writes

Result:
Test is passing all the time where it was sometimes fail before.
2014-04-23 09:28:20 +02:00
Norman Maurer
7ae40ace32 [#2400] Not close LocalChannel during deregister() to allow register to other EventLoop
Motivation:
At the moment it is not possible to deregister a LocalChannel from its EventLoop and register it to another one as the LocalChannel is closed during the deregister.

Modification:
Not close the LocalChannel during dergister

Result:
It is now possible to deregister a LocalChannel and register it to another EventLoop
2014-04-21 10:07:42 +02:00
Norman Maurer
9e02a9bbee Move validatePromise(...) to ChannelHandlerInvokerUtil. Related to [#2398]
Motivation:
Once a user implement a custom ChannelHandlerInvoker it is needed to validate the ChannelPromise. We should expose a utility method for this.

Modifications:
Move validatePromise(...) from DefaultChannelHandlerInvoker to ChannelHandlerInvokerUtil and make it public.

Result:
User is able to reuse code
2014-04-17 16:01:26 +02:00
Norman Maurer
9b670d819f [#2144] Fix NPE in Local transport caused by a race
Motivation:
At the moment it is possible to see a NPE when the LocalSocketChannels doRegister() method is called and the LocalSocketChannels doClose() method is called before the registration was completed.

Modifications:
Make sure we delay the actual close until the registration task was executed.

Result:
No more NPE
2014-04-17 15:06:52 +02:00
Norman Maurer
20ef4690e7 [#2375] [#2404] Fix bug in respecting ChannelConfig.setAutoRead(false) and also fix Channel.read() for OIO
Motivation:
At the moment ChanneConfig.setAutoRead(false) only is guaranteer to not have an extra channelRead(...) triggered when used from within the channelRead(...) or channelReadComplete(...) method. This is not the correct behaviour as it should also work from other methods that are triggered from within the EventLoop. For example a valid use case is to have it called from within a ChannelFutureListener, which currently not work as expected.

Beside this there is another bug which is kind of related. Currently Channel.read() will not work as expected for OIO as we will stop try to read even if nothing could be read there after one read operation on the socket (when the SO_TIMEOUT kicks in).

Modifications:
Implement the logic the right way for the NIO/OIO/SCTP and native transport, specific to the transport implementation. Also correctly handle Channel.read() for OIO transport by trigger a new read if SO_TIMEOUT was catched.

Result:
It is now also possible to use ChannelConfig.setAutoRead(false) from other methods that are called from within the EventLoop and have direct effect.

Conflicts:
	transport-sctp/src/main/java/io/netty/channel/sctp/nio/NioSctpChannel.java
	transport/src/main/java/io/netty/channel/socket/nio/NioDatagramChannel.java
	transport/src/main/java/io/netty/channel/socket/nio/NioSocketChannel.java
2014-04-17 07:50:51 +02:00
Norman Maurer
17334a0a42 [#2390] Minimize memory usage of NioDatagramChannel
Motivation:
At the moment we create a HashMap that holds the MembershipKeys for multicast with every NioDatagramChannel even when most people not need it at al

Modifications:
Lazy create the HashMap when needed.

Result:
Less memory usage and less object creation
2014-04-15 06:56:17 +02:00
Norman Maurer
88481131be [#2353] Use a privileged block to get ClassLoader and System property if needed
Motivation:
When using System.getProperty(...) and various methods to get a ClassLoader it will fail when a SecurityManager is in place.

Modifications:
Use a priveled block if needed. This work is based in the PR #2353 done by @anilsaldhana .

Result:
Code works also when SecurityManager is present
2014-04-08 14:12:25 +02:00
Norman Maurer
1087160fa7 [#2363] SelectedSelectionKeySet may hold strong reference to SelectionKey after Channel is closed
Motivation:
Because we not null out the array entry in the SelectionKey[] which is produced by SelectedSelectionKeySet.flip() we may end up with a few SelectionKeyreferences still hanging around here even after the Channel was closed. As these entries may be present at the end of the SelectionKey[] which is never updated for a long time as not enough SelectionKeys are ready.

Modifications:
Once we access the SelectionKey out of the SelectionKey[] we directly null it out.

Result:
Reference can be GC'ed right away once the Channel was closed.
2014-04-05 19:31:12 +02:00
Norman Maurer
fdb1db90c4 [#2362] AbstractChannel.AbstractUnsafe.write(...) is slow
Motivation:
At the moment we do a Channel.isActive() check in every AbstractChannel.AbstractUnsafe.write(...) call which gives quite some overhead as shown in the profiler when you write fast enough. We can eliminate the check and do something more smart here.

Modifications:
Remove the isActive() check and just check if the ChannelOutboundBuffer was set to null before, which means the Channel was closed. The rest will be handled in flush0() anyway.

Result:
Less overhead when doing many write calls
2014-04-04 09:54:52 +02:00
Norman Maurer
772a9d2610 [#2349] Correctly handle cancelled ChannelPromise in DefaultChannelHandlerContext
Motivation:
At the moment an IllegalArgumentException will be thrown if a ChannelPromise is cancelled while propagate through the ChannelPipeline. This is not correct, we should just stop to propagate it as it is valid to cancel at any time.

Modifications:
Stop propagate the operation through the ChannelPipeline once a ChannelPromise is cancelled.

Result:
No more IllegalArgumentException when cancel a ChannelPromise while moving through the ChannelPipeline.
2014-03-31 07:53:22 +02:00
Trustin Lee
844362a947 User-definable thread model via ChannelHandlerInvoker
Motivation:

While the default thread model provided by Netty is reasonable enough for most applications, some users might have a special requirement for the thread model.  Here are a few examples:

- A user might want to invoke handlers from the caller thread directly, assuming that his or her application is completely asynchronous and does not make any invocation from non-I/O thread.  In this case, the default invoker implementation will only add the overhead of checking if the current thread is an I/O thread or not.
- A user might want to invoke handlers from different threads depending on the type of events flexibly.

Modifications:

- Backport 132af3a485 which is a fix for #1912
  - Add a new interface called 'ChannelHandlerInvoker' that performs the invocation of event handler methods.
  - Add pipeline manipulation methods that accept ChannelHandlerInvoker
- The differences from the original commit:
  - Separated the irrelevant changes out
  - Channel.eventLoop is null until the registration is complete in this branch, so Channel.Unsafe.invoker() doesn't work before registration.
  - Deregistration is not gone in this branch, so the methods related with deregistration were added to ChannelHandlerInvoker
2014-03-24 18:09:27 +09:00
Trustin Lee
6d4c4d9e4b Correct the return type of MultithreadEventLoopGroup.newChild()
Motivation:

MultithreadEventLoopGroup.newChild() does not override MultithreadEventExecutorGroup.newChild() which returns EventExecutor.  MultithreadEventLoopGroup.newChild() should never return an EventExecutor, so this is incorrect.

Modifications:

Override MultithreadEventLoopGroup.newChild() so that it returns EventLoop

Result:

Correct API
2014-03-24 17:05:36 +09:00
Trustin Lee
aeb6ba5684 Update the Javadoc of ChannelHandler and ChannelHandlerContext
Motivation:

It's out of date and it has broken links, etc.

Modifications:

Backport the fixes from master (132af3a485)

Result:

Better Javadoc
2014-03-24 16:07:53 +09:00
Trustin Lee
7dc63ccd95 Add EventExecutor.children() in favor of iterator()
Motivation:

EventExecutor.iterator() is fixed to return Iterator<EventExecutor> and there's no way to change that as long as we don't extend Iterable.  However, a user should have a way to cast the returned set of executors painlessly.  Currently, it is only possible with an explicit cast like (Iterator<NioEventLoop>).

Modifications:

Instead, I added a new method called 'children()' which returns an immutable collection of child executors whose method signature looks like the following:

    <E extends EventExecutor> Set<E> children();

Result:

A user can now do this:

    Set<NioEventLoop> loops = group.children();
    for (NioEventLoop l: loops) { ... }

Unfortunately, this is not possible:

    for (NioEventLoop l: group.children()) { ... }

However, it's still a gain that a user doesn't need to down-cast explicitly and to add the '@SuppressWarnings` annotation.
2014-03-24 12:32:55 +09:00
Trustin Lee
1e3b7d8273 Replace LocalEventLoopGroup with DefaultEventLoopGroup
Motivation:

LocalEventLoopGroup and LocalEventLoop are not really special for LocalChannels.  It can be used for other channel implementations as long as they don't require special handling.

Modifications:

- Add DefaultEventLoopGroup and DefaultEventLoop
- Deprecate LocalEventLoopGroup and make it extend DefaultEventLoopGroup
- Add DefaultEventLoop and remove LocalEventLoop
- Fix inspector warnings

Result:

- Better class names.
2014-03-24 11:39:55 +09:00
Trustin Lee
007694b963 Implement EventExecutor.parent() in AbstractEventExecutor
Motivation:

EventExecutor.parent() and EventLoop.parent() almost always return a constant parent executor.  There's not much reason to let it implemented in subclasses.

Modifications:

- Implement AbstractEventExecutor.parent() with an additional contructor
- Add AbstractEventLoop so that subclasses extend AbstractEventLoop, which implements parent() appropriately
- Remove redundant parent() implementations in the subclasses
- Fix inspector warnings

Result:

Less duplication.
2014-03-24 11:05:51 +09:00
CoNDoRip
ac5e838398 Allow specifying SelectorProvider when constructing an NIO channel #2311
Motivation:

At the moment we use the system-wide default selector provider for this invocation of the Java virtual machine when constructing a new NIO channel, which makes using an alternative SelectorProvider practically useless.
This change allows user specify his/her preferred SelectorProvider.

Modifications:

Add SelectorProvider as a param for current `private static *Channel newSocket` method of NioSocketChannel, NioServerSocketChannel and NioDatagramChannel.
Change default constructors of NioSocketChannel, NioServerSocketChannel and NioDatagramChannel to use DEFAULT_SELECTOR_PROVIDER when calling newSocket(SelectorProvider).
Add new constructors for NioSocketChannel, NioServerSocketChannel and NioDatagramChannel which allow user specify his/her preferred SelectorProvider.

Result:

Now users can specify his/her preferred SelectorProvider when constructing an NIO channel.
2014-03-23 15:57:46 +01:00
Trustin Lee
b5c97bcc82 Use the length of MAC address as the last property to compare to get the best MAC address
Motivation:

Some operating systems like Windows 7 uses a valid globally unique EUI-64 MAC address for a virtual device (e.g. 00:00:00:00:00:00:00:E0), and because it's usually longer than the legit MAC-48 address, we should not use the length of MAC address when two MAC addresses are of the same quality.  Instead, we should compare the INET address of the NICs before comparing the length of the MAC addresses.

Modification:

Compare the length of MAC addresses as a last resort.

Result:

Correct MAC address detection in Windows with IPv6 enabled.
2014-03-21 12:58:58 +09:00
Trustin Lee
3613d2d59e Prefer the NIC with global IP address when getting the default machine ID
Motivation:

When there are two MAC addresses which are good enough, we can choose the one with better IP address rather than just choosing the first appeared one.

Modification:

Replace isBetterAddress() with compareAddresses() to make it return if both addresses are in the same preference level.
Add compareAddresses() which compare InetAddresses and use it when compareAddress(byte[], byte[]) returns 0 (same preference)

Result:

More correct primary MAC address detection
2014-03-21 12:32:26 +09:00
Trustin Lee
ff179c3430 Reduce the time taken by NetUtil and DefaultChannelId class initialization
Motivation:

As reported in #2331, some query operations in NetworkInterface takes much longer time than we expected.  For example, specifying -Djava.net.preferIPv4Stack=true option in Window increases the execution time by more than 4 times.  Some Windows systems have more than 20 network interfaces, and this problem gets bigger as the number of unused (virtual) NICs increases.

Modification:

Use NetworkInterface.getInetAddresses() wherever possible.
Before iterating over all NICs reported by NetworkInterface, filter the NICs without proper InetAddresses.  This reduces the number of candidates quite a lot.
NetUtil does not query hardware address of NIC in the first place but uses InetAddress.isLoopbackAddress().
Do not call unnecessary query operations on NetworkInterface.  Just get hardware address and compare.

Result:

Significantly reduced class initialization time, which should fix #2331.
2014-03-21 11:39:41 +09:00
Norman Maurer
afcc7fb7cc [#2326] Add constructor to NioServerSocketChannel which accepts a ServerSocketChannel
Motivation:
Allow the user to create a NioServerSocketChannel from an existing ServerSocketChannel.

Modifications:
Add an extra constructor

Result:
Now the user is be able to create a NioServerSocketChannel from an existing ServerSocketChannel, like he can do with all the other Nio*Channel implemntations.
2014-03-16 07:03:14 -07:00
Norman Maurer
9a11c43463 [#2323] Make it clear a Channel must be closed to release all resources
Motivation:
Ensure the user know the Channel must be closed to release resources like filehandles.

Modifications:
Add some extra javadoc.

Result:
More clear documentation
2014-03-16 07:02:57 -07:00
Norman Maurer
69d3cf5539 [#2308] Use SelectorProvider.open*() to open NIO channels and so remove condition when create new NIO channels.
Motivation:
At the moment we use SocketChannel.open(), ServerSocketChannel.open() and DatagramSocketChannel.open(...) within the constructor of our
NIO channels. This introduces a bottleneck if you create a lot of connections as these calls delegate to SelectorProvider.provider() which
uses synchronized internal. This change removed the bottleneck.

Modifications:
Obtain a static instance of the SelectorProvider and use SelectorProvider.openSocketChannel(), SelectorProvider.openServerSocketChannel() and
SelectorProvider.openDatagramChannel(). This eliminates the bottleneck as SelectorProvider.provider() is not called on every channel creation.

Result:
Less conditions when create new channels.
2014-03-13 07:00:33 +01:00
Norman Maurer
adcc2d4b4b Remove condition in ChannelHandlerAdapter.isSharable() by caching the result of the annotation lookup.
Motivation:
Remove the synchronization bottleneck and so speed up things

Modifications:
Introduce a ThreadLocal cache that holds mappings between classes of ChannelHandlerAdapater implementations and the result of checking if the @Sharable annotation is present.
This way we only will need to do the real check one time and server the other calls via the cache. A ThreadLocal and WeakHashMap combo is used to implement the cache
as this way we can minimize the conditions while still be sure we not leak class instances in containers.

Result:
Less conditions during adding ChannelHandlerAdapter to the ChannelPipeline
2014-03-12 12:31:52 +01:00
Norman Maurer
95ff172c82 Corrected inconsistencies in the Javadoc.
Port of 80030493b9f7824c02dc88260c2579afc0aed8bc
2014-03-04 06:34:50 +01:00
Jakob Buchgraber
dd38c8fa78 Added asserts to make sure ChannelHandlers are removed from the pipeline 2014-03-03 06:43:45 +01:00
Norman Maurer
d3ffa1b02b [#1259] Add optimized queue for SCMP pattern and use it in NIO and native transport
This queue also produces less GC then CLQ when make use of OneTimeTask
2014-02-27 13:28:37 +01:00
Norman Maurer
8c68c5a3ae Fix check to clear READ_OP and EPOLLIN. Part of [#2254] 2014-02-22 20:06:52 +01:00
Norman Maurer
b32316b33c [#2254] Correctly handle Channel.read() and ChannelHandlerContext.read()
This includes also when it is called from channelRead(...) and channelReadComplete(...) methods.
2014-02-22 18:48:47 +01:00
Norman Maurer
47fab2bfe8 Directly use memory addresses for gathering writes to reduce gc pressure. Part of [#2239]
This also does factor out some logic of ChannelOutboundBuffer. Mainly we not need nioBuffers() for many
transports and also not need to copy from heap to direct buffer. So this functionality was moved to
NioSocketChannelOutboundBuffer. Also introduce a EpollChannelOutboundBuffer which makes use of
memory addresses for all the writes to reduce GC pressure
2014-02-21 13:37:33 +01:00
Norman Maurer
78db65d0fb [#2254] Fix regression in handling autoRead and Channel.read()
This regression was introduced by e0b39159657c9eb711047bc32367537c4870d467
2014-02-21 09:19:36 +01:00
Norman Maurer
1c9c797e82 Move marking ChannelPromise for writes uncancellable to addFlush for keep things simple 2014-02-17 16:16:08 +01:00
Trustin Lee
a0e74ff984 Use thread local direct buffer for I/O when the current allocator is unpooled
- Allocating and deallocating a direct buffer for I/O is an expensive
  operation, so we have to at least have a pool of direct buffers if the
  current allocator is not pooled
2014-02-15 11:24:01 -08:00
Trustin Lee
fbd4385506 Determine the default allocator from system property
- Add ByteBufAllocator.DEFAULT
- The default allocator is now 'pooled'
2014-02-14 13:04:12 -08:00
Trustin Lee
0e4c80b953 Fix IllegalStateException caused by ChannelHandlerAppender 2014-02-13 19:44:40 -08:00
Trustin Lee
c671103289 Deprecate CombinedChannelDuplexHandler in favor of ChannelHandlerAppender
- Fixes #2233
- Add ChannelHandlerAppender
2014-02-13 19:20:56 -08:00
Trustin Lee
7e1db4feb7 Deprecate CombinedChannelDuplexHandler in favor of ChannelHandlerAppender
- Fixes #2233
2014-02-13 19:20:25 -08:00
Trustin Lee
ac70dc4546 Update the version to 4.1.0.Alpha1-SNAPSHOT 2014-02-13 18:32:26 -08:00
Trustin Lee
8837afddf8 Enable a user specify an arbitrary information with ReferenceCounted.touch()
- Related: #2163
- Add ResourceLeakHint to allow a user to provide a meaningful information about the leak when touching it
- DefaultChannelHandlerContext now implements ResourceLeakHint to tell where the message is going.
- Cleaner resource leak report by excluding noisy stack trace elements
2014-02-13 18:16:25 -08:00
Trustin Lee
0235244e55 Touch a ReferenceCounted while it traverses across a pipeline 2014-02-13 18:11:54 -08:00
Trustin Lee
45e70d9935 Add ReferenceCounted.touch() / Add missing retain() overrides
- Fixes #2163
- Inspector warnings
2014-02-13 18:10:11 -08:00
Trustin Lee
7e60877bc5 Merge the attribute map of ChannelHandlerContext into Channel
- Fixes #2136
- Also fixes some generics warnings
2014-02-13 18:02:44 -08:00
Trustin Lee
1d577a8d95 Get the PID properly on Android
- Related: #2109
2014-02-13 17:37:22 -08:00
Trustin Lee
d97f72d2c9 Fix a problem where DefaultChannelId prevents Netty 5 from running on Android
- Fixes #2109
- Use reflection to find the current PID
2014-02-13 17:35:44 -08:00
Trustin Lee
2b84314fdd Add Recycler.Handle.recycle() so that it's possible to recycle an object without an explicit reference to Recycler 2014-02-13 17:24:37 -08:00
Trustin Lee
df346a023b Change the return type of EmbeddedChannel.read*() from Object to an ad-hoc type parameter
.. so that there's no need to explicitly down-cast.

Fixes #2067
2014-02-13 17:19:26 -08:00
Vladimir Krivosheev
eb308cfff6 ability to use Executor instead of ThreadFactory 2014-02-13 16:14:41 -08:00
Trustin Lee
780516471f Bring back ChannelGroup.find(id) 2014-02-13 15:53:45 -08:00
Trustin Lee
40003ed250 Resurrect Channel.id() with global uniqueness
- Fixes #1810
- Add a new interface ChannelId and its default implementation which generates globally unique channel ID.
- Replace AbstractChannel.hashCode with ChannelId.hashCode() and ChannelId.shortValue()
- Add variants of ByteBuf.hexDump() which accept byte[] instead of ByteBuf.
2014-02-13 15:53:07 -08:00
Trustin Lee
812481602a Don't create an EmbeddedSocketAddress every time 2014-02-13 15:45:47 -08:00
Trustin Lee
499033d44f Add a shortcut method for collision-free naming 2014-02-13 15:17:09 -08:00
Trustin Lee
b533a1361b Replace UniqueName with Constant and ConstantPool
- Proposed fix for #1824

UniqueName and its subtypes do not allow getting the previously registered instance.  For example, let's assume that a user is running his/her application in an OSGi container with Netty bundles and his server bundle.  Whenever the server bundle is reloaded, the server will try to create a new AttributeKey instance with the same name.  However, Netty bundles were not reloaded at all, so AttributeKey will complain that the name is taken already (by the previously loaded bundle.)

To fix this problem:

- Replaced UniqueName with Constant, AbstractConstant, and ConstantPool.  Better name and better design.

- Sctp/Udt/RxtxChannelOption is not a ChannelOption anymore.  They are just constant providers and ChannelOption is final now.  It's because caching anything that's from outside of netty-transport will lead to ClassCastException on reload, because ChannelOption's constant pool will keep all option objects for reuse.

- Signal implements Constant because we can't ensure its uniqueness anymore by relying on the exception raised by UniqueName's constructor.
2014-02-13 15:14:34 -08:00
Trustin Lee
2d96b32155 Clean-up ChannelOutboundBufferTest
- partial port of 136e1ebba8
2014-02-13 14:50:11 -08:00
Trustin Lee
a65f097d53 Allow empty handler list when creating a new EmbeddedChannel
.. so that it can be used for dynamically initialized pipelines

- Fixes #1899
2014-02-13 14:46:33 -08:00
Norman Maurer
517da2b46a Fix checkstyle 2014-02-13 14:36:14 -08:00
Bill Gallagher
7e5aa4a911 use enum for state in LocalChannel 2014-02-13 14:35:58 -08:00
Bill Gallagher
a19fe06928 use enum for state in EmbeddedChannel 2014-02-13 14:34:51 -08:00
Trustin Lee
449ce0dd7a Remove the irrelevant AIO channel options 2014-02-13 13:59:12 -08:00
Trustin Lee
faaff9bd86 Backport the tests in ReentrantChannelTest
- Originally from c149f4bcc0 by @wgallagher
2014-02-13 13:55:39 -08:00
Norman Maurer
69a36b8bea Prettify exception message 2014-02-13 06:46:51 +01:00
Norman Maurer
62ebe88981 Allow to set IoRatio to 100% 2014-02-12 15:22:39 +01:00
Norman Maurer
80e6f9adf4 Correctly respect isAutoRead() and make it consistent across OIO/NIO 2014-02-11 20:46:46 +01:00
Norman Maurer
7041a9238e Allow to cancel non-flushed writes 2014-02-11 19:42:49 +01:00
Trustin Lee
d52dc3b740 Do not warn if failed to mark a void promise as success
- it's always supposed to fail.
2014-02-10 15:03:46 -08:00
Trustin Lee
96b0a949e1 Make most outbound operations cancellable / More robust promise update
- Inspired by #2214 by @normanmaurer
- Call setUncancellable() before performing an outbound operation
- Add safeSetSuccess/Failure() and use them wherever
2014-02-10 14:57:18 -08:00
Trustin Lee
041d37e0c8 Make most outbound operations are cancellable
- Inspired by #2214
- It actually reduces the chance of trying to marking a cancelled promise as success again, which raises an IllegalStateException.
2014-02-10 14:06:54 -08:00
Norman Maurer
87602fde25 [#2215] DefaultChannelHandlerContext tasks needs to be volatile to ensure every thread only see full initialized instances 2014-02-08 10:33:44 +01:00
Norman Maurer
9bee78f91c Provide an optimized AtomicIntegerFieldUpdater, AtomicLongFieldUpdater and AtomicReferenceFieldUpdater 2014-02-06 20:08:45 +01:00
Norman Maurer
64c3f58279 Not wakeup the EventLoop for writes as they will not cause a flush anyway 2014-02-01 13:45:27 +01:00
Norman Maurer
f94b563bcd Better exception message to tell the user why it is not supported 2014-01-30 07:02:22 +01:00
Norman Maurer
80ed147652 [#2164] Only reregister SelectionKeys that are still valid 2014-01-29 07:18:29 +01:00
Trustin Lee
9b0e5b9148 Fix API documentation on the usage of AttributeKey 2014-01-28 13:59:11 +09:00
Norman Maurer
f0c7c901d0 Add testcase to try to reproduce #2144 2014-01-23 07:04:42 +01:00
Norman Maurer
d67184b488 [maven-release-plugin] prepare for next development iteration 2014-01-21 08:18:32 +01:00
Norman Maurer
287515210d [maven-release-plugin] prepare release netty-4.0.15.Final 2014-01-21 08:18:26 +01:00
William Kemper
39b8cc348a fix grouping for isActive - socket.isBound is almost always true and should not override 'isOpen' 2014-01-17 07:14:00 +01:00
Trustin Lee
237ba27499 Better exception message 2014-01-13 23:32:49 +09:00
Trustin Lee
3373f83cbb Fix a bug where DefaultChannelPipelineTest.testFireChannelRegistered() triggers channelRegistered() twice 2014-01-13 23:25:32 +09:00
Norman Maurer
13d65d7ccf [#2104] Make sure we only act on the SelectionKey if it is valid 2014-01-09 18:27:56 +01:00
Trustin Lee
751943ed00 Fix a potential NPE due to the race between a connection attempt and its cancellation
- should fix #2086
2014-01-09 19:24:44 +09:00
Norman Maurer
0bbc3facec [#2086] Fix race which could produce NPE in AbstractNioUnsafe.finishConnect 2014-01-09 08:22:34 +01:00
milenkovicm
393f7b2306 ChannelOutboundBuffer returns total pending write size
total pending write size may be used to optimize write batching
2014-01-07 06:52:07 +01:00
Veebs
dd8f4bc0c4 Fix typo 2014-01-03 11:15:14 +01:00
Trustin Lee
e83d2e0b4e [maven-release-plugin] prepare for next development iteration 2013-12-22 21:57:48 +09:00
Trustin Lee
cdb700c7a4 [maven-release-plugin] prepare release netty-4.0.14.Final 2013-12-22 21:57:40 +09:00
Trustin Lee
0b7aedb13b [maven-release-plugin] rollback the release of netty-4.0.14.Final 2013-12-22 21:53:24 +09:00
Trustin Lee
4bf6ec7171 [maven-release-plugin] prepare release netty-4.0.14.Final 2013-12-22 21:52:56 +09:00
Trustin Lee
9c1a49c58e [maven-release-plugin] rollback the release of netty-4.0.14.Final 2013-12-22 21:47:35 +09:00
Trustin Lee
008a049bf4 [maven-release-plugin] prepare for next development iteration 2013-12-22 21:43:55 +09:00
Trustin Lee
f6cb9088c6 [maven-release-plugin] prepare release netty-4.0.14.Final 2013-12-22 21:43:45 +09:00
Norman Maurer
fc2e6916d9 Fix regression which was introduced by 89a7cb8e71
Related to [#2060]
2013-12-21 21:39:51 +01:00
Trustin Lee
bab227213e Increase the default maxMessagesPerRead of AbstractNioByteChannel to 16
- Related: #2079
2013-12-21 20:08:42 +09:00
Trustin Lee
1fcd19a28f Fix a bug where adaptive recvbuf size prediction doesn't work correctly when maxMessagesPerRead is > 1 2013-12-21 19:57:11 +09:00
Norman Maurer
b889d3f559 [#2079] Stop reading once the NIO byte Channel was complete drained 2013-12-21 10:38:07 +01:00
Trustin Lee
89a7cb8e71 More graceful registration failure
- Fixes #2060
- Ensure to return a future/promise implementation that does not fail with 'not registered to an event loop' error for registration operations
- If there is no usable event loop available, GlobalEventExecutor.INSTANCE is used as a fallback.
2013-12-21 18:08:58 +09:00
Trustin Lee
ceaebd37ed Rename flushAndWrite() to writeAndFlush()
- Fixes: #2066
- Fixed inspection warnings
2013-12-16 15:02:13 +09:00
Trustin Lee
82b6e75b96 Rename flushAndWrite() to writeAndFlush()
- Related: #2066
2013-12-16 14:58:40 +09:00
Norman Maurer
e136227ee6 [#2065] Fix NPE in AbstractOioByteChannel during write to the socket 2013-12-15 11:41:04 +01:00
Trustin Lee
419b5a8de7 Disable logging temporarily when running testRegistrationAfterShutdown 2013-12-08 14:18:39 +09:00
Trustin Lee
0097b904b7 Disable logging temporarily when running testRegistrationAfterShutdown2 2013-12-08 14:13:43 +09:00
Trustin Lee
4116de8360 Fix NoSuchElementException raised by ChannelInitializer
.. again.
2013-12-07 11:04:40 +09:00
Trustin Lee
02703e8fc1 Revert "Fix NoSuchElementException raised by ChannelInitializer"
This reverts commit 3c453f5dba.
2013-12-07 11:04:33 +09:00
Norman Maurer
b3d8c81557 Fix all leaks reported during tests
- One notable leak is from WebSocketFrameAggregator
- All other leaks are from tests
2013-12-07 00:44:56 +09:00
Trustin Lee
51428004b3 Fix NoSuchElementException raised by ChannelInitializer 2013-12-07 00:39:21 +09:00
Norman Maurer
17f5865e38 [maven-release-plugin] prepare for next development iteration 2013-11-29 19:31:01 +01:00
Norman Maurer
ead617fdcc [maven-release-plugin] prepare release netty-4.0.14.Beta1 2013-11-29 19:30:55 +01:00
Norman Maurer
6cf2748dbb [maven-release-plugin] prepare for next development iteration 2013-11-28 15:04:51 +01:00
Norman Maurer
5fe7596f49 [maven-release-plugin] prepare release netty-4.0.13.Final 2013-11-28 15:04:46 +01:00
Trustin Lee
407f0a36f5 Simplify bundle generation / Add io.netty.versions.properties to all JARs
- Fixes #2003 properly
- Instead of using 'bundle' packaging, use 'jar' packaging.  This is
  more robust because some strict build tools fail to retrieve the
  artifacts from a Maven repository unless their packaging is not 'jar'.
- All artifacts now contain META-INF/io.netty.version.properties, which
  provides the detailed information about the build and repository.
- Removed OSGi testsuite temporarily because it gives false errors
  during split package test and examination.
- Add io.netty.util.Version for easy retrieval of version information
2013-11-26 22:01:46 +09:00
Norman Maurer
7ec70d0210 Merge package private interfaces into public ones. Related to [#1989] and [#1991] 2013-11-25 10:37:34 +01:00
Trustin Lee
fd776274c9 Additional fix for potential race condition which occurs when a user cancels a connection attempt
- Fixes #1986
2013-11-18 17:00:43 +09:00
Trustin Lee
54d3c99469 Fix an unexpected IllegalStateException from a selector loop when a user cancels a connection attempt
- Fixes #1986
2013-11-18 16:33:21 +09:00
Trustin Lee
ec10409314 Saner toString() implementation for EmbeddedSocketAddress 2013-11-08 18:04:40 +09:00
Norman Maurer
db78581bbb [maven-release-plugin] prepare for next development iteration 2013-11-07 18:11:45 +01:00
Norman Maurer
2386777af8 [maven-release-plugin] prepare release netty-4.0.12.Final 2013-11-07 18:11:38 +01:00
Norman Maurer
7dddbbb2bd Fix possible leak when a write is rejected 2013-11-07 10:24:15 +01:00
Norman Maurer
77054d7ecb Fix regression which lead to leak buffers when nothing could be read from the Channel.
This was introduced as part of #1812, but fortunatualy was not part of any release.
2013-11-07 07:12:19 +01:00
Trustin Lee
d2032254b7 Enable AUTO_CLOSE opton by default for backward compatibility / Deprecare AUTO_CLOSE option because it's gone in 5.0.
- Related #1952
2013-11-05 17:40:23 +09:00
Trustin Lee
c7b66545b4 Add AUTO_CLOSE option
- Fixes #1952
- If AUTO_CLOSE is turned on, Netty will close the channel immediately and automatically on write failure.  The default is false.
2013-11-05 17:24:36 +09:00
Trustin Lee
54db9ec725 Use StringUtil.simpleClassName(..) instead of Class.getSimpleName() where necessary
- Class.getSimpleName() doesn't render anonymous classes very well
- + some minor cleanup
2013-11-04 19:46:15 +09:00
Norman Maurer
e9967e55ad [#1940] Add javadoc to explain how the FileChannel is closed when using DefaultFileRegion 2013-11-02 15:59:33 +01:00
Trustin Lee
e1baa3f9b4 Simplify 2013-11-02 20:03:41 +09:00
Trustin Lee
72c78ebe75 Add an important notice about future migration issue in SimpleChannelInboundHandler.
- Related: #1590
2013-11-02 20:03:15 +09:00
Norman Maurer
b53fa5dd70 [#1812] All to have NioMessageUnsafe.read() inlined 2013-10-26 17:44:25 +02:00
Trustin Lee
8986245b47 Deprecate UniqueName and its subtypes' constructors / Add valueOf() for easier future migration. 2013-10-25 20:53:47 +09:00
Norman Maurer
544d68b396 [#1812] Allow for inline for most common cases when use NioByteUnsafe.read() 2013-10-25 13:32:21 +02:00
Norman Maurer
e4358ae6b8 [#1947] Handle RejectExecutionException graceful for outbound operations 2013-10-25 07:51:17 +02:00
Norman Maurer
ceab146b54 [maven-release-plugin] prepare for next development iteration 2013-10-21 07:43:42 +02:00
Norman Maurer
27a89d6032 [maven-release-plugin] prepare release netty-4.0.11.Final 2013-10-21 07:41:49 +02:00
Norman Maurer
9fd8bf329d More efficient handling of incomplete writes.
The problem with the old way was that we always set the OP_WRITE when the buffer could not be written
until the write-spin-count was reached. This means that in some cases the channel was still be writable
but we just was not able to write out the data quick enough. For this cases we should better break out the
write loop and schedule a write to be picked up later in the EventLoop, when other tasks was executed.
The OP_WRITE will only be set if a write actual returned 0 which means there is no more room for writing data
and this we need to wait for the os to notify us.
2013-10-17 20:23:47 +09:00
Norman Maurer
53fcff2eab [#1920] Fix IndexOutOfBoundsException when using PooledByteBufAllocator with SCTP and NIO Datagram channels 2013-10-16 09:53:26 +02:00
Norman Maurer
df442b9b6a #1924] Only log RejectExecutorException when call invokeLater(...) 2013-10-15 15:22:46 +02:00
Norman Maurer
068c75a025 [#1924] Correctly fail promise when EventExecutor was shutdown in between deregister 2013-10-15 14:01:59 +02:00
Trustin Lee
c9b7f1f1b5 Ensure the selector implementation can be instrumented before attempting instrumentation
- Fixes #1908
2013-10-11 12:08:51 +09:00
Trustin Lee
d7f9b1ee76 Fixes the problem where the promise of the outbound operation that causes a channel closure is notified after channelInactive()
- Fixes #1897
2013-10-08 12:24:16 +09:00
Norman Maurer
20a16ae8dc Use direct ByteBuf for the test to make sure it is not copied 2013-10-07 08:08:10 +02:00
Norman Maurer
c0936fc8e7 [#1890] Correctly expand ByteBuffer array in all cases
The problem was that we did not handle the case correctly when doubling the array was not enough. We need to keep doubling until everything fits in.
2013-10-06 15:29:35 +02:00
Norman Maurer
d7da19f745 [maven-release-plugin] prepare for next development iteration 2013-10-02 15:48:52 +02:00
Norman Maurer
d35768ae11 [maven-release-plugin] prepare release netty-4.0.10.Final 2013-10-02 15:48:45 +02:00
Bill Gallagher
013ac44d3a [#1832] - Channel writability change notifications sometimes fail to fire 2013-09-30 20:01:39 +02:00
Norman Maurer
b4fa8af079 Cache underlying ByteBuffers and count in ChannelOutboundBuffer.Entry to reduce object creation and so GC pressure
Beside this it also helps to reduce CPU usage as nioBufferCount() is quite expensive when used on CompositeByteBuf which are
nested and contains a lot of components
2013-09-26 20:37:39 +02:00
Norman Maurer
ae904a1f56 Introduce a new ChannelOption called DATAGRAM_CHANNEL_ACTIVE_ON_REGISTRATION. Related to [#1830]
This ChannelOption allows to tell the DatagramChannel implementation to be active as soon as they are registrated to their EventLoop. This can be used to make it possible to write to a not bound DatagramChannel.
The ChannelOption is marked as @deprecated as I'm looking for a better solution in master which breaks default behaviour with 4.0 branch.
2013-09-24 11:46:49 +02:00
Sasha Zverev
a2624a833e Slip in DefaultOioSocketChannelConfig (setAllowHalfClosure used to ignore argument) 2013-09-21 20:13:52 +02:00
Norman Maurer
f034f90fb3 [#1836] Add comment to explain why read is triggered 2013-09-17 06:58:47 +02:00
Norman Maurer
357677d8fa [#1830] Add testcase for write to not bound DatagramChannel impls and revert change in OIO as it breaks things as the udnerlying socket lazy binds 2013-09-12 09:27:43 +02:00
Norman Maurer
f4f04a08c2 Make DatagramChannel impls .isActive() return true when the underlying Channel is open. This also fixes [#1830] 2013-09-11 20:37:21 +02:00
Norman Maurer
7d9388a3cc Allow to only register a Channel via AbstractBootstrap and bind/connect it later. Related to [#1829] 2013-09-11 20:14:53 +02:00
Norman Maurer
ffab456aca Bump up version to reflect correct one 2013-09-09 11:20:12 +02:00
Norman Maurer
af499b5fb4 Mark ChannelHandler.exceptionCaught(...) as deprecated in preparation to move to ChannelInboundHandler. Related to [#1808] 2013-09-08 20:11:51 +02:00
Norman Maurer
363531caf9 [maven-release-plugin] rollback the release of netty-4.0.9.Final 2013-09-06 09:18:34 +02:00
Norman Maurer
9d53573ee8 [maven-release-plugin] prepare for next development iteration 2013-09-06 09:17:15 +02:00
Trustin Lee
ad0c456209 Ensure operationProgressed is invoked even on completion
- Fixes #1809
2013-09-05 18:37:14 +09:00
Norman Maurer
92cec8d2ac Split up the nioBuffers() method to allow for inline. Related to #1812
This move less common method patterns to extra methods and so make the nioBuffers() method with most common pattern (backed by one ByteBuffer) small enough for inlining.
2013-09-05 09:22:13 +02:00
Norman Maurer
c97971b53a [#1805] Fix example in javadocs of SimpleChannelInboundHandler 2013-09-03 20:30:56 +02:00
Norman Maurer
25c226a835 Make sure only direct ByteBuffer are passed to the underlying jdk Channel.
This is needed because of otherwise the JDK itself will do an extra ByteBuffer copy with it's own pool implementation. Even worth it will be done
multiple times if the ByteBuffer is always only partial written. With this change the copy is done inside of netty using it's own allocator and
only be done one time in all cases.
2013-09-02 20:17:53 +02:00
Norman Maurer
4a5c840271 @Deprecated ChannelOutboundHandler.deregister(...) 2013-09-01 12:54:29 +02:00
Norman Maurer
b8866aef33 No need to check instanceof everytime to find the next inbound / outbound context 2013-08-30 06:31:58 +02:00
Norman Maurer
32deb2c22b [#1785] Fix incorrect javadocs 2013-08-27 06:55:14 +02:00
Norman Maurer
2e39b25cd4 [maven-release-plugin] prepare for next development iteration 2013-08-26 12:01:03 +02:00
Norman Maurer
b67659a866 [maven-release-plugin] prepare release netty-4.0.8.Final 2013-08-26 12:00:54 +02:00
Norman Maurer
5e9b199296 @deprecated all methods which are related to deregister as it will be removed in 4.1.0.Final 2013-08-26 11:36:56 +02:00
Norman Maurer
80d30c3dd8 Small code improvements 2013-08-26 07:52:47 +02:00
Norman Maurer
77d4222db5 [#1777] Use correct Thread when close per channel 2013-08-25 21:22:53 +02:00
Norman Maurer
f76c01c3aa [#1782] Fix IndexOutOfBoundException with direct buffer and gathering writes 2013-08-24 18:16:05 +02:00
Trustin Lee
7aefd0cbdb Make AbstractBootstrap public
.. to work around the issue with JDK reflection described here:

  http://bugs.sun.com/bugdatabase/view_bug.do?bug_id=4283544

Fixes #1780
2013-08-24 17:20:53 +09:00
Norman Maurer
9ca20b73d3 Add testcase to show channelRegistered is called 2013-08-23 17:17:28 +02:00
bgallagher
51fa795819 fix race condition in test 2013-08-23 16:20:02 +02:00
Norman Maurer
206dc2a391 [#1772] Make sure ChannelOutboundBuffer.recycle() does also reset unflushed, flushed and tail.
This fix a IndexOutOfBoundsException which as triggered if recycle() did cut down the buffer[] to the initial size.
2013-08-23 09:01:16 +02:00
Norman Maurer
9fd35d09a2 [#1770] Fix NPE which was thrown if connection timeout was disabled and the connect did not finish directly when using NIO 2013-08-22 12:38:56 +02:00
bgallagher
6a2f340ec0 trim buffers before recycling 2013-08-21 20:28:54 +02:00
bgallagher
fb619f2394 fix writability callback 2013-08-21 16:39:50 +02:00
Norman Maurer
217b8e255c [#1763] Fill ChannelOutboundBuffer.nioBuffers with null on close to allow the content to be GC'ed 2013-08-20 21:15:05 +02:00
Trustin Lee
15cfa47ad9 Fix checkstyle 2013-08-20 14:40:28 +09:00
Trustin Lee
caf91b9c06 Fix IllegalStateException triggered while shutting down ThreadPerChannelEventLoopGroup
- Fix #1718
- Add the test case contributed by @mkw
2013-08-20 14:37:57 +09:00
bgallagher
a383988cdb add struct to replace parallel arrays consolidate flushed & unflushed buffers 2013-08-18 19:19:57 +02:00
bgallagher
06e250e493 remove unused initialCapacity 2013-08-17 14:10:33 +02:00
bgallagher
9f88552f12 remove some dead code 2013-08-10 20:46:48 +02:00
Norman Maurer
280afda013 [#1715] Remove extra call socket.configureBlocking(false) 2013-08-10 20:33:19 +02:00
bgallagher
59c2fd8813 [#1723] invoke close in eventloop 2013-08-10 08:19:16 +02:00
Norman Maurer
9d8c4ded50 Move method in correct scope 2013-08-09 13:30:04 +02:00
Norman Maurer
4d0621855a Remove unused package private method and so remove some complexity 2013-08-09 11:44:41 +02:00
Norman Maurer
b54937ab50 [#1711] Allow to use ChannelOption for set / get MessageSizeEstimator 2013-08-08 20:37:35 +02:00
Norman Maurer
f40a3f34b1 [#1692] Allow to set WRITE_BUFFER_HIGH_WATER_MARK and WRITE_BUFFER_LOW_WATER_MARK via ChannelOption 2013-08-08 20:30:01 +02:00
Norman Maurer
1d3560e389 [maven-release-plugin] prepare for next development iteration 2013-08-08 13:53:28 +02:00
Norman Maurer
8e97e6c461 [maven-release-plugin] prepare release netty-4.0.7.Final 2013-08-08 13:53:19 +02:00
Norman Maurer
fc6213604d Make sure ChannelOutboundBuffer not throw NPE during increment/decrement pending writes 2013-08-08 13:42:25 +02:00
Norman Maurer
b934b6009c Share some code, related to [#1707]] 2013-08-07 20:28:33 +02:00
Norman Maurer
5ef30b6d8b [#1707] More efficient implementation of ChannelHandlerContext.writeAndFlush(..) 2013-08-07 20:15:10 +02:00
Norman Maurer
5b6e762bf4 Allow to have the Channel GC'ed ASAP 2013-08-07 10:32:03 +02:00
Norman Maurer
48a7a21541 Correctly update Channel.isWritable() when the write happens from outside the EventLoop in a fast fashion. Fixes [#1697]
Introduce a new interface called MessageSizeEstimator. This can be specific per Channel (via ChannelConfig). The MessageSizeEstimator will be used to estimate for a message that should be written. The default implementation handles ByteBuf, ByteBufHolder and FileRegion. A user is free to plug-in his/her own implementation for different behaviour.
2013-08-07 10:10:43 +02:00
Norman Maurer
de44917e62 Use recyclable write task to reduce GC pressure 2013-08-05 14:59:58 +02:00
Trustin Lee
17b91f416d Remove an irrelevant comment
.. because firedChannelActive is gone long ago
2013-08-05 16:50:25 +09:00
Norman Maurer
3f2000fa3a [maven-release-plugin] prepare for next development iteration 2013-08-01 10:59:55 +02:00
Norman Maurer
3f70d5caa4 [maven-release-plugin] prepare release netty-4.0.6.Final 2013-08-01 10:59:46 +02:00
Norman Maurer
a06295fe0a Correctly fix problem in ByteToMessageDecoder and ReplayingDecoder which could let to have a released buffer passed to the decode methods.
This fixes #1664 and revert also the original commit which was meant to fix it 3b1881b523 . The problem with the original commit was that it could delay handlerRemove(..) calls and so mess up the order or forward bytes to late.
2013-08-01 09:54:07 +02:00
Norman Maurer
e3410680de [maven-release-plugin] prepare for next development iteration 2013-07-31 20:08:14 +02:00
Norman Maurer
0e124583d6 [maven-release-plugin] prepare release netty-4.0.5.Final 2013-07-31 20:08:05 +02:00
Trustin Lee
81de2275e4 Remove unnecessary traversal of pipeline which occurs when a Channel is closed
- Remove unnecessary ascending traversal of pipeline in DefaultChannelHandlerContext.freeInbound()
- Move DefaultChannelHandlerContext.teardownAll() to DefaultChannelPipeline
2013-07-31 20:45:37 +09:00
Trustin Lee
3b1881b523 Make sure ChannelHandler.handlerRemoved() is invoked while handler methods are not running
- Fixes #1664
2013-07-31 20:35:51 +09:00
Norman Maurer
3049f5ddc4 Fix checkstyle 2013-07-31 12:21:50 +02:00
Trustin Lee
c79a3cdefe Fix a bug in NioSocketChannel.doWrite() where flush() triggered from a ChannelFutureListener is ignored
- Fixes #1679
2013-07-31 19:13:45 +09:00
Norman Maurer
ca29f1a37d [#1683] Mark unused ChannelOption @deprecated, to prepare for removal in 4.1.0.Final 2013-07-31 10:50:39 +02:00
Trustin Lee
e81368af06 Simplify handler invocations in DefaultChannelHandlerContext
- Sometimes we delegated executor.inEventLoop() to the next context and sometimes we did not.  Now we always check inEventLoop() before delegating.
2013-07-31 16:34:32 +09:00
Norman Maurer
e09aea5902 Rename methods of EmbeddedChannel and mark old ones as @deprecated 2013-07-31 16:04:08 +09:00
Jeff Pinner
3922c518cd Clean up AbstractUnsafe#bind and AbstractUnsafe#disconnect. 2013-07-29 06:54:42 +02:00
Jeff Pinner
bf2430d255 Change AbstractChannel#doRegister return type from Runnable to void. 2013-07-27 20:22:02 +02:00
Jeff Pinner
ca59c1201e Change AbstractChannel#doDeregister return type from Runnable to void. 2013-07-26 22:21:41 +02:00
Norman Maurer
15279b2525 [#1654] Notify close future after the close was complete 2013-07-26 14:21:11 +02:00
Norman Maurer
cffbba94ee [#1654] Remove AbstractChannel.doPreClose() and notify close future on register failure. Based on patch of @jpinner 2013-07-26 14:10:31 +02:00
Norman Maurer
5f363e8ade Revert "remove AbstractChannel#doPreClose"
This reverts commit 241f856cc7.
2013-07-26 11:23:11 +02:00
Jeff Pinner
241f856cc7 remove AbstractChannel#doPreClose 2013-07-26 10:12:01 +02:00
Norman Maurer
fabefba791 [#1650] Make it possible to override isSharable() to simplify things for clojure users 2013-07-25 20:24:27 +02:00
Norman Maurer
6ff87cc20d Small optimitation to limit volatile reads 2013-07-25 09:28:54 +02:00
Trustin Lee
5e4169802f Fix potential reentrance issue in ChannelOutboundBuffer 2013-07-24 11:26:03 +09:00
Norman Maurer
0bc7d3f5d1 [maven-release-plugin] prepare for next development iteration 2013-07-23 10:04:23 +02:00
Norman Maurer
ca00182797 [maven-release-plugin] prepare release netty-4.0.4.Final 2013-07-23 10:04:14 +02:00
Norman Maurer
0b17586731 [#1623] Fix javadocs for ChannelGroup 2013-07-23 09:03:42 +02:00
Trustin Lee
7903697c36 Remove Arrays.fill(..., null)
.. because we can just set each element to null while looping
2013-07-23 15:09:14 +09:00
Trustin Lee
a89b17fa94 Merge ChannelOutboundBuffer.failUnflushed() and recycle() into a single method and make sure it is run later on reentrance
- Previously, failUnflushed() did not run when inFail is true, which made unflushed writes are not released on reentrance.   This has been fixed by this commit.
- Also, AbstractUnsafe.outboundBuffer is set to null as early as possible to remove the chance of any write attempts made after the closure.
2013-07-23 14:34:10 +09:00
Trustin Lee
d4aa5b53d6 Simplify the validation logic proposed in 25f96b1644 2013-07-23 13:48:22 +09:00
kerr
ada07cb9e0 Fix types in javadocs 2013-07-22 19:14:36 +02:00
Norman Maurer
25f96b1644 [#1606] Reduce overhead during writes because of ChannelPromise validation 2013-07-22 11:28:02 +02:00
Norman Maurer
81612f8e9b [#1624] Fix resource leak when writing to a closed / not-open channel 2013-07-22 10:59:06 +02:00
Norman Maurer
0f6cc0cc7b [#1630] Fix re-entrance bug in ChannelOutboundBuffer.remove(...) 2013-07-22 10:44:33 +02:00
tsingxu
125070958d Fix up ChannelPipeline javadocs by add lost "don't " 2013-07-22 07:14:42 +02:00
Norman Maurer
7f86550ef8 [#1619] Fix bug in ChannelOutboundBuffer which could lead to invalid write order when fireChannelWritabilityChanged() write another message 2013-07-20 10:03:53 +02:00
Norman Maurer
60529ac3ee Fix checkstyle 2013-07-20 08:09:08 +02:00
Jeff Pinner
6c9c151d66 minor documentation cleanup 2013-07-20 08:01:14 +02:00
Norman Maurer
4d69848aec Fix broken javadocs 2013-07-19 07:40:12 +02:00
Trustin Lee
19c92ceb59 Separate 'progress total' and 'pending number of bytes'
- Reverted the recent changes in AbstractChannel.calculateMessageSize()
2013-07-19 14:09:08 +09:00
Trustin Lee
762adfcb69 Update HttpStaticFileServer example / Fix bugs related with progress notification
- Fix a bug in DefaultProgressivePromise.tryProgress() where the notification is dropped
 - Fix a bug in AbstractChannel.calculateMessageSize() where FileRegion is not counted
 - HttpStaticFileServer example now uses zero copy file transfer if possible.
2013-07-19 13:21:32 +09:00
Trustin Lee
f96a8e5951 Implement ProgressivePromise notification in NIO byte channels and ChunkedWriteHandler
- Refine the contract of GenericProgressiveFutureListener.
- Negative 'total' now means 'unknown', which is useful for ChunkedWriteHandler.
2013-07-19 12:53:23 +09:00
Trustin Lee
0653efcd75 Even better promise validation messages 2013-07-19 09:38:25 +09:00
Trustin Lee
d5e202d755 Better promise validation messages 2013-07-19 09:37:56 +09:00
Trustin Lee
faf8b76b5a Fix a potential bug where AbstractUnsafe.flush0() fails to clear the inFlush0 flag
- Fixes #1609
2013-07-19 08:56:17 +09:00
Trustin Lee
8178322c5c A little bit of Javadoc for ChannelOutboundBuffer 2013-07-19 01:17:00 +09:00
Trustin Lee
fef838f197 Make sure channelInactive() and channelDeregistered() are triggered even if outboundBuffer.recycle() fails 2013-07-19 01:09:19 +09:00
Trustin Lee
8828d5327a Move inFlush0 and outboundBuffer in AbstractChannel to AbstractUnsafe
.. because they are accessed by AbstractUnsafe much more often.
2013-07-18 23:33:39 +09:00
Trustin Lee
5e5df6bd09 Fix NPE 2013-07-18 23:29:13 +09:00
Trustin Lee
4cd7e62555 Make ChannelOutboundBuffer recycled 2013-07-18 23:26:45 +09:00
Trustin Lee
46ea0d4e7b Implement gathering writes in NioSocketChannel
- Add some support methods in ChannelOutputBuffer
2013-07-18 23:14:39 +09:00
Trustin Lee
4f0a952241 Checkstyle 2013-07-18 21:01:01 +09:00
Trustin Lee
bcef796dc7 Rewrite ChannelOutboundBuffer
- Merge MessageList into ChannelOutboundBuffer
- Make ChannelOutboundBuffer a queue-like data structure so that it is nearly impossible to leak a message
- Make ChannelOutboundBuffer public so that AbstractChannel can expose it to its subclasses.
- TODO: Re-enable gathering write in NioSocketChannel
2013-07-18 20:59:14 +09:00
Trustin Lee
b130ee6a6c [maven-release-plugin] prepare for next development iteration 2013-07-18 11:17:42 +09:00
Trustin Lee
10d395e829 [maven-release-plugin] prepare release netty-4.0.3.Final 2013-07-18 11:17:31 +09:00
Trustin Lee
568166d554 Cleanup 2013-07-18 10:29:34 +09:00
Trustin Lee
473af5c98e Fix checkstyle 2013-07-18 10:25:16 +09:00
Trustin Lee
e28594952b Make the cleanup logic in ChannelOutboundBuffer more robust
- Fixes #1601
2013-07-18 10:23:26 +09:00
Trustin Lee
9c8d980a74 Fix a bug where a ChannelFutureListener can allow Unsafe.close() and Unsafe.flush() to overlap and reenter from flush() to close().
- Fixes #1600
2013-07-18 10:14:55 +09:00
Norman Maurer
fc7c950b08 [maven-release-plugin] prepare for next development iteration 2013-07-17 15:58:36 +02:00
Norman Maurer
bbbf72359e [maven-release-plugin] prepare release netty-4.0.2.Final 2013-07-17 15:58:28 +02:00
Trustin Lee
88cbdb50d2 Fail unflushed writes with ClosedChannelException
... instead of cryptic exception message.
2013-07-17 21:25:51 +09:00
Trustin Lee
5f235eafc3 Fix checkstyle 2013-07-17 21:17:52 +09:00
Trustin Lee
31ecd17212 Fix test failure 2013-07-17 21:16:52 +09:00
Trustin Lee
cc9b9567b9 Make sure all write attempts made after a channel is closed are marked as failure 2013-07-17 21:14:07 +09:00
Trustin Lee
a8d67b0282 Fix data structure corruption and resource leak in ChannelOutboundBuffer 2013-07-17 21:02:56 +09:00
Trustin Lee
dcf7896172 Do not close ServerChannel on IOException while accepting an incoming connection
.. so that we can recover from 'too many open files'

- Fixes #1578
2013-07-16 18:39:29 +09:00
Trustin Lee
57eb531eb8 [maven-release-plugin] prepare for next development iteration 2013-07-16 17:16:10 +09:00
Trustin Lee
76cefcc421 [maven-release-plugin] prepare release netty-4.0.1.Final 2013-07-16 17:15:54 +09:00
Norman Maurer
5297eba280 [maven-release-plugin] prepare for next development iteration 2013-07-15 15:48:15 +02:00
Norman Maurer
c5d8af446a [maven-release-plugin] prepare release netty-4.0.0.Final 2013-07-15 15:48:05 +02:00
Trustin Lee
246a3ecdcb [maven-release-plugin] prepare for next development iteration 2013-07-15 20:58:33 +09:00
Trustin Lee
e8fd209115 [maven-release-plugin] prepare release netty-4.0.0.Final 2013-07-15 20:58:21 +09:00
Norman Maurer
2de491aa7f Use UnpooledByteBufAllocator as default 2013-07-15 10:44:33 +02:00
Norman Maurer
d5f052f39c Rename ChannelGroupMatcher to ChannelMatcher 2013-07-15 10:42:36 +02:00
Norman Maurer
9dfad35423 Fix checkstyle 2013-07-14 18:32:10 +02:00
Norman Maurer
75997545ed Fix checkstyle 2013-07-14 18:13:47 +02:00
Norman Maurer
c20c852602 More javadoc fixes 2013-07-14 18:04:33 +02:00
Norman Maurer
43d22f6d23 Remove unused class which was package private anyway 2013-07-14 17:54:07 +02:00
Norman Maurer
a07abee55f Add and correct javadocs 2013-07-13 19:42:02 +02:00
Norman Maurer
2af7db361b [#1573] Fix NPE which could be triggered one failed promises that trigger a close89 2013-07-12 22:57:03 +02:00
Norman Maurer
2871079c4a [#1557] Make the contract of Channel.Unsafe.flush() more clear
* Remove boolean parameter from Channel.Unsafe.flush() method
* Move NIO related things to AbstractNioChannel.NioUnsafe
2013-07-12 19:45:31 +02:00
Trustin Lee
660729bd56 Kill the cruft 2013-07-12 20:41:29 +09:00
Trustin Lee
456994607b || -> && 2013-07-12 20:32:49 +09:00
Trustin Lee
99716993f6 Add a boolean parameter to Channel.Unsafe.flush() so that SelectionKey state check can be bypassed. 2013-07-12 20:14:50 +09:00
Trustin Lee
e10e9d38c4 Fix embarassing compilation error :-/ 2013-07-12 20:12:18 +09:00
Trustin Lee
85a2ba3752 Remove dead code
- Fixed #1557
2013-07-12 20:10:39 +09:00
Trustin Lee
6d1220b55e Reduce garbage in AbstractUnsafe.flush0() 2013-07-12 20:04:01 +09:00
Trustin Lee
529d904d29 Fix a bug where ChannelOutboundBuffer.addFlush() is called multiple times 2013-07-12 20:01:38 +09:00
Trustin Lee
e2fcb06d9a Remove unnecessary try-catch block in AbstractUnsafe.flush() 2013-07-12 20:00:30 +09:00
Norman Maurer
43f12569aa Cache flush(..) tasks which are used when executing with different EventExecutor to lower GC pressure 2013-07-12 11:57:33 +02:00
Norman Maurer
aa64c13bb8 Cleanup 2013-07-12 11:48:26 +02:00
Norman Maurer
d23c3b3382 Introduce ChannelGroupMatcher which can be used to only apply operations of a ChannelGroup on matching Channels.
This is often useful if you for example use a ChannelGroup to hold all connected Channels and want to broadcast a message too all of them
except one Channel.
2013-07-11 10:58:53 +02:00
Norman Maurer
12ea35fd5f Add missing javadocs 2013-07-11 10:26:10 +02:00
Jeff Pinner
224f05e626 Use correct permission mode for java files 2013-07-10 21:58:12 +02:00
Trustin Lee
b7a7c33fe3 Fix a bug in ChannelOutboundBuffer.addFlush()
It should not advance the tail if no write() was issued so far.
2013-07-11 01:05:26 +09:00
Norman Maurer
b57d9f307f Allow per-write promises and disallow promises on flush()
- write() now accepts a ChannelPromise and returns ChannelFuture as most
  users expected.  It makes the user's life much easier because it is
  now much easier to get notified when a specific message has been
  written.
- flush() does not create a ChannelPromise nor returns ChannelFuture.
  It is now similar to what read() looks like.
2013-07-11 00:49:48 +09:00
Norman Maurer
dd763698dc Adjust ChannelGroup to behave the same like a Channel in terms of write and flush 2013-07-10 08:27:11 +02:00
Trustin Lee
7bedd8f28e Simplify the exception handling of ChannelOutboundHandler.write()
DefaultChannelHandlerContext does not trigger exceptionCaught() immediately when ChannelOutboundHandler.write() raises an exception.  It just records the exception until flush() is triggered.  On invokeFlush(), if there's any exception recorded, DefaultChannelHandlerContext will fail the promise without calling ChannelOutboundHandler.flush().  If more than one exception were raised, only the first exception is used as the cause of the failure and the others will be logged at warn level.
2013-07-10 00:36:47 +09:00
Trustin Lee
26e9d70457 Remove channelReadSuspended / Rename messageReceived(Last) to channelRead(Complete)
- Remove channelReadSuspended because it's actually same with messageReceivedLast
- Rename messageReceived to channelRead
- Rename messageReceivedLast to channelReadComplete

We renamed messageReceivedLast to channelReadComplete because it
reflects what it really is for.  Also, we renamed messageReceived to
channelRead for consistency in method names.
2013-07-09 23:58:51 +09:00
Trustin Lee
cbd8817905 Remove MessageList from public API and change ChannelInbound/OutboundHandler accordingly
I must admit MesageList was pain in the ass.  Instead of forcing a
handler always loop over the list of messages, this commit splits
messageReceived(ctx, list) into two event handlers:

- messageReceived(ctx, msg)
- mmessageReceivedLast(ctx)

When Netty reads one or more messages, messageReceived(ctx, msg) event
is triggered for each message.  Once the current read operation is
finished, messageReceivedLast() is triggered to tell the handler that
the last messageReceived() was the last message in the current batch.

Similarly, for outbound, write(ctx, list) has been split into two:

- write(ctx, msg)
- flush(ctx, promise)

Instead of writing a list of message with a promise, a user is now
supposed to call write(msg) multiple times and then call flush() to
actually flush the buffered messages.

Please note that write() doesn't have a promise with it.  You must call
flush() to get notified on completion. (or you can use writeAndFlush())

Other changes:

- Because MessageList is completely hidden, codec framework uses
  List<Object> instead of MessageList as an output parameter.
2013-07-09 23:51:48 +09:00
Trustin Lee
7396f9f2b2 Remove Channel.id completely / Use 64-bit hashCode internally to reduce the chance of collision in compareTo() 2013-07-09 14:49:06 +09:00
Norman Maurer
9c1b31d20a [#1535] Remove Channel.id() and so fix the possible leakage of the previous used Channel id map
The user can still use Channel.hashCode() for logging. It's just not 100% unique but should be good enough for most cases
2013-07-08 14:07:18 +02:00
Norman Maurer
39b57b889c [#1539] Fix bug in DefaultChannelGroup.close() which was blocking the close() call on ServerChannel 2013-07-08 13:36:39 +02:00
Trustin Lee
a52ac692a9 Faster MessageList iteration in NioSocketChannel.doWrite() 2013-07-07 15:15:52 +09:00
Trustin Lee
2b2f8db5d2 Use ThreadLocalRandom where possible 2013-07-07 12:37:36 +09:00
Norman Maurer
086ae3536c [#1533] Introduce ByteBufHolder.duplicate() and make use of it in DefaultChannelGroup.write(...) 2013-07-06 21:17:51 +02:00
Trustin Lee
eb8df35f21 Use MessageList.first() and last() wherever possible
- Related issue: #1530
2013-07-05 14:11:09 +09:00
Trustin Lee
b7e6a86c1e Add MessageList.first() and last() for convenience.
- Fixes #1530
2013-07-05 14:07:51 +09:00
Trustin Lee
0b9235f072 Simplify ByteBufProcessor and MessageListProcessor and Add internal component accessors to CompositeByteBuf
- Fixes #1528

It's not really easy to provide a general-purpose abstraction for fast-yet-safe iteration. Instead of making forEachByte() less optimal, let's make it do what it does really well, and allow a user to implement potentially unsafe-yet-fast loop using unsafe operations.
2013-07-05 14:00:46 +09:00
Norman Maurer
2bda1b530a [#1523] Fix bug which lead to have SelectedKeys handled two times and so caused a NPE on heavy load 2013-07-04 16:15:33 +02:00
Norman Maurer
08b75e594c [#1519] VoidChannelPromise don't fire CancellationException anymore which was incorrect 2013-07-04 09:32:38 +02:00
Norman Maurer
cea873286e [#1517] Only fire the exception throught the pipeline if the channel is registered when using VoidChannelPromise 2013-07-04 09:20:24 +02:00
Trustin Lee
998b408db3 Fix NPE in OioByteStreamChannel
- Do not assign null to 'is' and 'os' but assign an alternative stream implementation
2013-07-04 12:04:28 +09:00
Norman Maurer
7ec12d327f Remove deprecated ByteBufUtil.release(..) and ByteBufUtil.retain(..) methods and its usage. Also fix a problem where an object would have been released two times.
* The problem with the release(..) calls here was that it would have called release on an unsupported message and then throw an exception. This exception will trigger ChannelOutboundBuffer.fail(..), which will also try to release the message again.
* Also use the same exception type for unsupported messages as in other channel impls.
2013-07-03 10:00:13 +02:00
Norman Maurer
ec5e793a2f [maven-release-plugin] prepare for next development iteration 2013-07-02 11:41:18 +02:00
Norman Maurer
ca73eaef0d [maven-release-plugin] prepare release netty-4.0.0.CR9 2013-07-02 11:41:09 +02:00
Norman Maurer
830c559405 [maven-release-plugin] rollback the release of netty-4.0.0.CR9 2013-07-02 11:34:29 +02:00
Norman Maurer
66a16b133c [maven-release-plugin] prepare release netty-4.0.0.CR9 2013-07-02 10:45:12 +02:00
Trustin Lee
956c0f8b90 Better explanation of reentrance issue of ChannelOutboundBuffer 2013-07-02 17:22:56 +09:00
Norman Maurer
5437835832 [#1501] Fix NPE correctly which could accour if ChannelOutboundBuffer.fail(..) triggered another call to ChannelOutboundBuffer.fail(...) 2013-07-02 09:58:41 +02:00
Norman Maurer
8dfbcbda29 [#1501] Fix NPE which could accour if ChannelOutboundBuffer.fail(..) triggered another call to ChannelOutboundBuffer.fail(...) 2013-07-02 09:32:34 +02:00
Trustin Lee
7e3a01cc51 [maven-release-plugin] prepare for next development iteration 2013-07-02 10:26:48 +09:00
Trustin Lee
149db34c19 [maven-release-plugin] prepare release netty-4.0.0.CR8 2013-07-02 10:26:32 +09:00
Trustin Lee
efd9c94775 Use higher maxMessagesPerRead as default for ServerChannels
- Fixes #1493
2013-07-02 10:20:15 +09:00
Trustin Lee
26b56d3add Fix a bug in MessageList.add(T[])
- where it uses incorrect source index while iteration
2013-07-02 10:11:17 +09:00
Trustin Lee
720de2e6cc Add missing sanity check for DefaultChannelHandlerContext.write(...) 2013-07-02 09:36:01 +09:00
Trustin Lee
4b11aff08f Less confusing log messages for system properties
- Fixes #1502
2013-07-02 09:23:29 +09:00
Norman Maurer
5d88c423df [#1500] Remove @deprecated methods 2013-07-01 08:53:02 +02:00
Norman Maurer
617ab6321b [#1489] Correctly handle channelReadSuspended and channelWritabilityChanged in CombinedChannelDuplexHandler 2013-06-30 17:18:33 +02:00
Trustin Lee
613547b0b9 [maven-release-plugin] prepare for next development iteration 2013-06-28 22:15:33 +09:00
Trustin Lee
a6abd2feb2 [maven-release-plugin] prepare release netty-4.0.0.CR7 2013-06-28 22:15:20 +09:00
Trustin Lee
ea963c25c9 Improve Javadoc of ChannelPipeline
- Fixes #1226
2013-06-28 22:09:00 +09:00
Trustin Lee
5f1aa6afde Remove potentially misleading exception message
.. because the MessageList itself is not read-only.
2013-06-28 21:25:15 +09:00
Trustin Lee
591dce565a checkExclusive() -> checkIndex() 2013-06-28 21:17:18 +09:00
Trustin Lee
d4665f1703 Fix test failures 2013-06-28 21:14:23 +09:00
Trustin Lee
1e0146da3e Optimize MessageList.add(MessageList, int, int) 2013-06-28 20:53:57 +09:00
Trustin Lee
7cf88a1a3c Add MessageList.array() / Rewrite MessageList.add(T[], int, int)
- MessageList.array() should give better performance + concise code
- MessageList.add(T[], int, int) iterated over the source array 3 times at worst case. This commit reduces that to 1 time.
2013-06-28 20:47:19 +09:00
Trustin Lee
0dcf352f4c Vastly simplified ByteBufProcessor and MessageListProcessor
- Related: #1378
- They now accept only one argument.
- A user who wants to use a buffer for more complex use cases, he or she can always access the buffer directly via memoryAddress() and array()
2013-06-28 20:29:00 +09:00
Trustin Lee
52691488ee Update Javadoc of ByteBufProcessor and MessageListProcessor
- in response to @shacharo's suggestion
2013-06-27 19:01:01 +09:00
Trustin Lee
4dd9b6ef2e Add ByteBufProcessor and ByteBuf.forEach(...)
- Fixes #1378
- Needs to provide optimized forEach implementations though.
2013-06-27 13:55:42 +09:00
Trustin Lee
734ec51ac9 Allow specifying 0 as the default number of threads when instantiating an EventLoopGroup
- Fixes #1426
- We already allow a user instantiate an EventLoopGroup with the default number of threads via the default constructor, so I think it's OK although it's not always optimal.
2013-06-27 10:39:39 +09:00
Trustin Lee
bc483724f4 Improve the documentation of MessageList
- Fixes #1459
2013-06-25 18:27:29 +09:00
Trustin Lee
1f27c3b390 Make NioByteUnsafe.read() respect ChannelConfig.maxMessagesPerRead and adjust the default from 16 to 1
- Fixes #1486
- Decreased the default from 16 to 1 because unnecessary extra read on req-res protocols results in lower throughput due to extra syscalls.
2013-06-25 18:08:39 +09:00
Trustin Lee
a1632e7d15 Add ChannelConfig.maxMessagesPerRead and ChannelOption.MAX_MESSAGES_PER_READ
- Fixes #1486
- Make sure AbstractNioMessageChannel.NioMessageUnsafe.read() only up to maxMessagesPerRead
2013-06-25 17:49:28 +09:00
Trustin Lee
a6795d7780 [maven-release-plugin] prepare for next development iteration 2013-06-25 11:07:15 +09:00
Trustin Lee
2221446425 [maven-release-plugin] prepare release netty-4.0.0.CR6 2013-06-25 11:07:15 +09:00
Trustin Lee
c77f03d886 Fix AdaptiveRecvByteBufAllocator.getSizeTableIndex() 2013-06-25 11:07:15 +09:00
Norman Maurer
c9d01b2fb5 [#1461] Correctly handle DefaultChannelGroup.write(..) of ByteBuf and ByteBufHolder 2013-06-25 11:07:14 +09:00
Trustin Lee
cfb3b977a1 Fix the catastrophic failure caused by AdaptiveRecvByteBufAllocator.getSizeTableIndex() 2013-06-25 11:07:14 +09:00
Trustin Lee
a2f232720b Make AdaptiveRecvByteBufAllocator's lookup table simpler / Optimize buffer size normalization
- No need to have fine-grained lookup table because the buffer pool has
  much more coarse capacities available
- No need to use a loop to normalize a buffer capacity
2013-06-25 11:07:14 +09:00
Trustin Lee
a969613540 Merge ChannelInboundConsumingHandler into SimpleChannelInboundHandler
- SimpleChannelInboundHandler now has a constructor parameter to let a
  user decide to enable automatic message release. (the default is to
  enable), which makes ChannelInboundConsumingHandler of less value.
2013-06-25 11:07:14 +09:00
Norman Maurer
bfc9c6d80d Add ChannelInboundConsumingHandler
..which is useful when the handler is placed at the last position of the
pipeline because it releases the received messages automatically.
2013-06-25 11:07:14 +09:00
Tony Rice
6c5c119f8c Fix incorrect parameter validation in DefaultFileRegion 2013-06-25 11:07:14 +09:00
Norman Maurer
cce74efded [#1448] Don't print failure if VoidChannelPromise is used 2013-06-16 14:25:02 +02:00
Norman Maurer
6a9f965f9b Introduce new utility class calles ReferenceCountUtil and move utility methods from ByteBufUtil to it.
The ones in ByteBufUtil were marked as @deprecated
2013-06-14 07:07:33 +02:00
Norman Maurer
4bf5003f76 Don't release messages before throw UnsupportedOperationException, as the caller method will take care 2013-06-14 06:41:27 +02:00
Trustin Lee
a5871dfd86 [maven-release-plugin] prepare for next development iteration 2013-06-14 12:55:15 +09:00
Trustin Lee
f5377cc8d7 [maven-release-plugin] prepare release netty-4.0.0.CR5 2013-06-14 12:55:05 +09:00
Trustin Lee
fe40d4b67f Make sure writing to a closed channel does not trigger an UnsupportedOperationException
- Fixes #1442
2013-06-14 11:15:46 +09:00
Trustin Lee
25c51279cf Revert "[#1442] Make sure closing the channel will not cause an UnsupportedOperationException"
This reverts commit a1a86b9de4 because the
semantic of ctx.isRemoved() is confusing to a user - why is
ctx.isRemoved() false when handlerRemoved() is invoked? A better
solution would be check if the connection is inactive and mark the
promise as failure before attempting to write anything.
2013-06-14 10:47:31 +09:00
Trustin Lee
a0c082497a Remove unused exception classes 2013-06-14 10:21:41 +09:00
Norman Maurer
8edee3272a More javadoc fixes 2013-06-13 20:56:17 +02:00
Norman Maurer
dc070a00b2 Deprecate IncompleteFlushException as its not used anymore 2013-06-13 20:50:21 +02:00
Norman Maurer
9100256a56 Javadocs cleanup 2013-06-13 20:49:05 +02:00
Norman Maurer
0e16b22aa1 Deprecate NoSuchBufferException as it's not used anymore 2013-06-13 20:48:54 +02:00
Norman Maurer
a1a86b9de4 [#1442] Make sure closing the channel will not cause an UnsupportedOperationException 2013-06-13 18:10:56 +02:00
Trustin Lee
e5ca6518ba [maven-release-plugin] prepare for next development iteration 2013-06-13 17:02:32 +09:00
Trustin Lee
381063e09c [maven-release-plugin] prepare release netty-4.0.0.CR4 2013-06-13 17:02:19 +09:00
Trustin Lee
427d9c4bf2 Fix test failures and reported leaks 2013-06-13 15:18:11 +09:00
Trustin Lee
f178b8d421 Suppress duplicate warning message printed when a message reaches at the end of pipeline 2013-06-13 13:23:52 +09:00
Trustin Lee
175526b6bd Move ReferenceCounted and AbstractReferenceCounted to io.netty.util
- Fixes #1441
- Also move and rename IllegalBufferAccessException to ReferenceCountException
- Prettier reference count exception messages
2013-06-13 13:14:21 +09:00
Trustin Lee
283feda119 Reduce even more garbage by exposing ByteBuf.internalNioBuffer() 2013-06-13 12:40:26 +09:00
Trustin Lee
5131c024fa Tiny optimization 2013-06-13 12:15:41 +09:00
Trustin Lee
96380e756c Fix test failures introduced by 78d8f05c21 2013-06-13 11:51:03 +09:00
Trustin Lee
2088d1b491 Generate less garbage when performing gathering writes 2013-06-13 10:27:10 +09:00
Norman Maurer
d1a3806ebd Make use of gathering writes if a MessageList which only contains ByteBuf msgs is written to a NioSocketChannel 2013-06-12 09:45:33 +02:00
Trustin Lee
79e236dfc2 Make EventExecutor.shutdownGracefully() return Future
- Also added EventExecutor.terminationFuture()
- Also fixed type signature problem with Future.add/removeListener()
- Related issue: #1389
2013-06-12 08:00:54 +09:00
Trustin Lee
fd0084ecfa Remove the constructors that uses ImmediateEventExecutor from DefaultChannelGroup
.. which is incorrect in my opinion.

+ minor cleanup
2013-06-12 06:50:38 +09:00
Trustin Lee
7a1550631d Make write operation cancellation while it's in progress
.. which should be useful when writing a large buffer/file
2013-06-12 04:24:07 +09:00
Norman Maurer
5b978497f8 Cleanup 2013-06-11 16:24:06 +02:00
Trustin Lee
c3034c8964 Implement the cancellation of connection attmpe for NIO and OIO transport
- Related issue: #1432
- Also added test cases to validate the implementation
2013-06-11 18:46:39 +09:00
Trustin Lee
7a5cf48b8d Implement Promise/Future cancellation properly for outbound traffic
- Related issue: #1432
- Make sure the Promise of a write operation is not cancellable before writing out
2013-06-11 17:54:35 +09:00
Trustin Lee
41af9a1eb3 Implement cancellation properly for Promise/Future
- Related issue: #1432
- Add Future.isCancellable()
- Add Promise.setUncancellable() which is meant to be used for the party that runs the task uncancellable once started
- Implement Future.isCancelled() and Promise.cancel(boolean) properly
2013-06-11 17:46:21 +09:00
Norman Maurer
85afdda3ce Correctly write MessageList which contains more then one message 2013-06-11 10:30:15 +02:00
Norman Maurer
16e12b45f8 Use Correct NoSuchElementException 2013-06-11 07:57:35 +02:00
Norman Maurer
e4a985f6ac Let MessageList implement Iterable 2013-06-11 07:55:41 +02:00
Norman Maurer
f2f6d68d2e Make sure writing empty ByteBuf will not cause a stavation.
This also fixes [#1436]
2013-06-10 20:54:17 +02:00
Trustin Lee
3ce9ab2e72 Replace the sun.nio.ch.SelectorImpl.selectedKeys with faster one
- Yield much less garbage
- Slight performance gain (1~2%)
2013-06-11 00:00:55 +09:00
Norman Maurer
d9806c8127 Add javadocs 2013-06-10 14:23:40 +02:00
Norman Maurer
68c737f0c0 Optimize the way messages are added from one MessageList to another one 2013-06-10 14:07:25 +02:00
Norman Maurer
92bd4d2fe0 Remove MessageList.remove(*) , MessageList.set(*) and MessageList.add(i,*) 2013-06-10 13:44:01 +02:00
Norman Maurer
e9c6406819 Remove the AIO transport as NIO is just faster
The AIO transport was added in the past as we hoped it would have better latency as the NIO transport. But in reality this was never the case.
So there is no reason to use the AIO transport at all. It just put more burden on us as we need to also support it and fix bugs.
Because of this we dedicided to remove it for now. It will stay in the master_with_aio_transport branch so we can pick it up later again if it is ever needed.
2013-06-10 11:30:11 +02:00
Trustin Lee
65e4161e63 Remove an unnecessary empty line 2013-06-10 18:20:24 +09:00
Trustin Lee
fa205defa1 Simplify the logic for updating OP_WRITE in the NIO transport
- Removed code duplication
2013-06-10 18:19:58 +09:00
Norman Maurer
3be25694d0 Add ChannelHandlerContext.isRemoved() to easily detect the removal of a ChannelHandler while in a method. 2013-06-10 11:16:05 +02:00
Norman Maurer
fa6999cd42 [#1425] Allow to access the EventLoopGroups via the Bootstraps 2013-06-10 09:24:57 +02:00
Trustin Lee
14158070bf Revamp the core API to reduce memory footprint and consumption
The API changes made so far turned out to increase the memory footprint
and consumption while our intention was actually decreasing them.

Memory consumption issue:

When there are many connections which does not exchange data frequently,
the old Netty 4 API spent a lot more memory than 3 because it always
allocates per-handler buffer for each connection unless otherwise
explicitly stated by a user.  In a usual real world load, a client
doesn't always send requests without pausing, so the idea of having a
buffer whose life cycle if bound to the life cycle of a connection
didn't work as expected.

Memory footprint issue:

The old Netty 4 API decreased overall memory footprint by a great deal
in many cases.  It was mainly because the old Netty 4 API did not
allocate a new buffer and event object for each read.  Instead, it
created a new buffer for each handler in a pipeline.  This works pretty
well as long as the number of handlers in a pipeline is only a few.
However, for a highly modular application with many handlers which
handles connections which lasts for relatively short period, it actually
makes the memory footprint issue much worse.

Changes:

All in all, this is about retaining all the good changes we made in 4 so
far such as better thread model and going back to the way how we dealt
with message events in 3.

To fix the memory consumption/footprint issue mentioned above, we made a
hard decision to break the backward compatibility again with the
following changes:

- Remove MessageBuf
- Merge Buf into ByteBuf
- Merge ChannelInboundByte/MessageHandler and ChannelStateHandler into ChannelInboundHandler
  - Similar changes were made to the adapter classes
- Merge ChannelOutboundByte/MessageHandler and ChannelOperationHandler into ChannelOutboundHandler
  - Similar changes were made to the adapter classes
- Introduce MessageList which is similar to `MessageEvent` in Netty 3
- Replace inboundBufferUpdated(ctx) with messageReceived(ctx, MessageList)
- Replace flush(ctx, promise) with write(ctx, MessageList, promise)
- Remove ByteToByteEncoder/Decoder/Codec
  - Replaced by MessageToByteEncoder<ByteBuf>, ByteToMessageDecoder<ByteBuf>, and ByteMessageCodec<ByteBuf>
- Merge EmbeddedByteChannel and EmbeddedMessageChannel into EmbeddedChannel
- Add SimpleChannelInboundHandler which is sometimes more useful than
  ChannelInboundHandlerAdapter
- Bring back Channel.isWritable() from Netty 3
- Add ChannelInboundHandler.channelWritabilityChanges() event
- Add RecvByteBufAllocator configuration property
  - Similar to ReceiveBufferSizePredictor in Netty 3
  - Some existing configuration properties such as
    DatagramChannelConfig.receivePacketSize is gone now.
- Remove suspend/resumeIntermediaryDeallocation() in ByteBuf

This change would have been impossible without @normanmaurer's help. He
fixed, ported, and improved many parts of the changes.
2013-06-10 16:10:39 +09:00
Norman Maurer
89f1f3f4d1 [#1399] DefaultChannelHandlerPipeline.firstContext() should return null if no user handlers are in in the pipeline 2013-05-27 15:45:34 +02:00
Norman Maurer
f7931af704 Re-add Unsafe.voidPromise() which can be used for Unsafe operations for which no notification should be done [#1375] 2013-05-25 14:35:22 +02:00
Norman Maurer
f5dc482a59 No need to clear buffer as it is cleared later anyway and only update interestedOps if needed 2013-05-24 12:50:04 +02:00
Norman Maurer
d31ccebd62 Make sure that setAutoRead(false) has a direct effect and only update interestedOps if needed 2013-05-24 12:49:21 +02:00
Norman Maurer
252bd25855 Only call key.interestedOps() if needed 2013-05-24 12:46:30 +02:00
Trustin Lee
a3b4cdd614 Fix StackOverflowError in LocalEcho.doBeginRead() when the peer channel keeps writing data
- Fixes #1380
2013-05-24 11:55:21 +09:00
Norman Maurer
5398792ffa [#1388] Correctly break the loop on exceptions 2013-05-23 17:17:21 +02:00
Norman Maurer
50ac0cdfcb [#1388] Ensure AbstractNioMessageChannel based Channels will call fireInboundBufferUpdated() soon enough to release resources 2013-05-23 16:59:03 +02:00
Norman Maurer
9c925b104a [#1385] Fix NPE which was triggered if a write was executed but the HeadHandler not init yet 2013-05-23 07:42:01 +02:00
Norman Maurer
548540bc2d Fix a which could cause data corruption when using AioSocketChannel.
This was because it was possible to have the JDK read into a wrong buffer region if the user called discardReadBytes() later. Fixes #1377
2013-05-21 20:19:00 +02:00
Norman Maurer
81e3c1719a [maven-release-plugin] prepare for next development iteration 2013-05-18 09:59:13 +02:00
Norman Maurer
99caefdf39 [maven-release-plugin] prepare release netty-4.0.0.CR3 2013-05-18 09:57:11 +02:00
Norman Maurer
620c3e025a Just some tiny javadoc fixes 2013-05-17 22:16:29 +02:00
Norman Maurer
abb4e20d0b [#1369] Move ImmediateEventExecutor to common and let it access via a static
* Also fix a bug there to return a correct implementation of ProgressivPRomi
  ImmediateEventExecutor
2013-05-17 21:35:01 +02:00
Norman Maurer
a8830aee42 [#1369] Move ImmediateEventExecutor to common and let it access via a static public field
* Also fix a bug there to return a correct implementation of ProgressivPRomise to work with the
 ImmediateEventExecutor
2013-05-17 21:19:59 +02:00
Norman Maurer
6942dba855 [#1363] Make sure ChannnelConfig.setAutoRead(false) will stop read from socket directly 2013-05-17 20:56:09 +02:00
Norman Maurer
699ef0784e [#1317] Allow to use VoidPromise for flush(...), write(...) and sendFile(...)
* This also move rename Channel.Unsafe.voidFuture() to ChannelPropertyAccess.voidPromise()
2013-05-17 15:50:14 +02:00
Trustin Lee
fd1d31e7d8 Remove unnecessary inEventLoop() checks in Channel.Unsafe
.. because HeadHandler in the pipeline always ensures those methods are always invoked from the correct I/O thread
2013-05-17 19:20:46 +09:00
Trustin Lee
7140e4e63b Test if ChannelHandler.handlerRemoved() is called on closure / Reduced timeout 2013-05-17 11:07:53 +09:00
Trustin Lee
e1a378aa03 Clean up DefaultChannelPipelineTest
- Use the local transport in a correct way (i.e. no need to trigger channelActive et al by ourselves)
- Use Promise/Future instead of CountDownLatch where they simplifies
2013-05-17 10:54:20 +09:00
Trustin Lee
2040b07849 Free the cleared buffer as early as possible / Better naming 2013-05-16 19:41:02 +09:00
Trustin Lee
dc13b68632 Make sure ChannelHandler.handlerRemoved() is always invoked
- Fixes #1366: No elegant way to free non-in/outbound buffers held by a handler
- handlerRemoved() is now also invoked when a channel is deregistered, as well as when a handler is removed from a pipeline.
- A little bit of clean-up for readability
- Fix a bug in forwardBufferContentAndRemove() where the handler buffers are not freed (mainly because we were relying on channel.isRegistered() to determine if the handler has been removed from inside the handler.
- ChunkedWriteHandler.handlerRemoved() is unnecessary anymore because ChannelPipeline now always forwards the content of the buffer.
2013-05-16 19:32:39 +09:00
Trustin Lee
670d3f53a8 Make uninitialization code in DefaultChannel easier to understand
.. by fixing bad / outdated method names
2013-05-16 16:18:01 +09:00
Norman Maurer
c43950a03f [maven-release-plugin] prepare for next development iteration 2013-05-08 18:19:51 +02:00
Norman Maurer
ae76502040 [maven-release-plugin] prepare release netty-4.0.0.CR2 2013-05-08 18:19:38 +02:00
Norman Maurer
18bda09d6c Allow to recover from exception triggered by accept() more easily
This is done by stop accept() new sockets for 1 seconds
Beside this this commit also makes sure accept() exceptions of OioServerSocketChannel trigger
the fireExceptionCaught(...). The same is true fo the AioServerSocketChannel.
2013-05-08 17:21:14 +02:00
Norman Maurer
e48bc9c086 [#1344] Fix race condition in DefaultChannelPromise / DefaultChannelProgressivePromise which could lead to listeners that are not notified 2013-05-08 10:14:28 +02:00
Norman Maurer
a4a92ee14a Try to reproduce #1335 without luck 2013-05-06 10:29:14 +02:00
Norman Maurer
7b854072d4 [#1327] Fix javadoc diagram for new api 2013-05-02 13:22:31 +02:00
Trustin Lee
1e0c83db23 Introduce AddressedEnvelope message type for generic representation of an addressed message
- Fixes #1282 (not perfectly, but to the extent it's possible with the current API)
- Add AddressedEnvelope and DefaultAddressedEnvelope
- Make DatagramPacket extend DefaultAddressedEnvelope<ByteBuf, InetSocketAddress>
- Rename ByteBufHolder.data() to content() so that a message can implement both AddressedEnvelope and ByteBufHolder (DatagramPacket does) without introducing two getter methods for the content
- Datagram channel implementations now understand ByteBuf and ByteBufHolder as a message with unspecified remote address.
2013-05-01 17:04:43 +09:00
Trustin Lee
23d0178494 Introduce EventExecutor.shutdownGracefully() that deprecates shutdown()
shutdownGracefully() provides two optional parameters that give more
control over when an executor has to be shut down.

- Related issue: #1307
- Add shutdownGracefully(..) and isShuttingDown()
- Deprecate shutdown() / shutdownNow()
- Replace lastAccessTime with lastExecutionTime and update it after task
  execution for accurate quiet period check
  - runAllTasks() and runShutdownTasks() update it automatically.
  - Add updateLastExecutionTime() so that subclasses can update it
- Add a constructor parameter that tells not to add an unncessary wakeup
  task in execute() if addTask() wakes up the executor thread
  automatically.  Previously, execute() always called wakeup() after
  addTask(), which often caused an extra dummy task in the task queue.
- Use shutdownGracefully() wherever possible / Deprecation javadoc
- Reduce the running time of SingleThreadEventLoopTest from 40s to 15s
  using custom graceful shutdown parameters

- Other changes made along with this commit:
  - takeTask() does not throw InterruptedException anymore.
    - Returns null on interruption or wakeup
  - Make sure runShutdownTasks() return true even if an exception was
    raised while running the shutdown tasks
  - Remove unnecessary isShutdown() checks
  - Consistent use of SingleThreadEventExecutor.nanoTime()

Replace isWakeupOverridden with a constructor parameter
2013-05-01 10:52:38 +09:00
Trustin Lee
6646db171e Use tryFailure() to notify registration failure to avoid IllegalStateException
.. which is raised when the registration promise has been failed already due to an internal error in the pipeline.

- Fixes #1319
2013-04-30 18:30:17 +09:00
Norman Maurer
61327b5871 Simplify a bit 2013-04-30 07:17:07 +02:00
Trustin Lee
8bb6d5b303 Rename Unsafe.directOutboundContext to headContext 2013-04-26 10:23:01 +09:00
Trustin Lee
7884574c7b Remove freeInboundBuffer() and freeOutboundBuffer() which has no value
- Fixes #1308

freeInboundBuffer() and freeOutboundBuffer() were introduced in the early days of the new API when we did not have reference counting mechanism in the buffer. A user did not want Netty to free the handler buffers had to override these methods.

However, now that we have reference counting mechanism built into the buffer, a user who wants to retain the buffers beyond handler's life cycle can simply return the buffer whose reference count is greater than 1 in newInbound/OutboundBuffer().
2013-04-25 09:15:55 +09:00
Trustin Lee
1b3d7f5325 Make sure handlerAdded() is called before forwarding the buffer content of the removed handler
- Added a test case that reproduces the problem in ReplayingDecoderTest
- Call newHandler.handlerAdded() *before* oldHandler.handlerRemoved() to ensure newHandlerAdded() is called before forwarding the buffer content of the old handler in replace0().
2013-04-24 19:25:43 +09:00
Trustin Lee
99b999760a Move multiplicity check to the early stage
.. no need to do it late
2013-04-24 19:02:34 +09:00
Trustin Lee
6282b31bc0 Format 2013-04-24 18:57:14 +09:00
Trustin Lee
7c5dc363fb Rename methods to catch up the recent changes in handler life cycle listener methods / Ensure to call handlerRemoved() even if ctx.forwardContentAndRemove() failed 2013-04-24 18:55:51 +09:00
Trustin Lee
c72b5341a3 ChannelHandler.handlerRemoved() must be invoked *after* the handler has been removed completely and its buffers should be inaccessible. 2013-04-24 18:46:35 +09:00
Trustin Lee
a68d39fcf2 Fix an infinite exception storm triggered by DefaultChannelHandlerContext.invokeInboundBufferUpdated()
- it has to break from the infinite loop when an exception is raised by handler
2013-04-24 18:39:34 +09:00
Trustin Lee
b5989e2449 Reduce exception instantiation overhead in SslHandler / Reduce unnecessary empty array creation
- Added EmptyArrays as an internal utility class
2013-04-24 09:32:53 +09:00
Trustin Lee
d292fdafdd Make sure to close the accept channel which couldn't be initialized or added to the message buffer 2013-04-23 22:42:47 +09:00
Trustin Lee
cc0ad9f1cc Fix hanging SocketBufReleaseTest / Make sure AioServerSocketChannel closes the accepted channel when the server socket is being shut down 2013-04-23 22:38:28 +09:00
Trustin Lee
f03b2cde62 Fix intermittent infinite loop in AbstractOioByteChannel.doRead()
- OioByteStreamChannel.doReadBytes() did not expand the capacity of the inbound buffer properly.
2013-04-23 22:12:07 +09:00
Trustin Lee
f149cf5220 Reduce code duplication 2013-04-23 13:42:00 +09:00