A grep on xorg/* revealed there's no consumer of this define.
Quote Alan Coopersmith:
"The consumer was in past versions of the headers now located
in proto/x11proto - for instance, in X11R6.0's xc/include/Xproto.h,
all the event definitions were only available if NEED_EVENTS were
defined, and all the reply definitions required NEED_REPLIES.
Looks like Xproto.h dropped them by X11R6.3, which didn't have
the #ifdef's anymore, so these are truly ancient now."
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Save in a few special cases, _X_EXPORT should not be used in C source
files. Instead, it should be used in headers, and the proper C source
include that header. Some special cases are symbols that need to be
shared between modules, but not expected to be used by external drivers,
and symbols that are accessible via LoaderSymbol/dlopen.
This patch also adds conditionally some new sdk header files, depending
on extensions enabled. These files were added to match pattern for
other extensions/modules, that is, have the headers "deciding" symbol
visibility in the sdk. These headers are:
o Xext/panoramiXsrv.h, Xext/panoramiX.h
o fbpict.h (unconditionally)
o vidmodeproc.h
o mioverlay.h (unconditionally, used only by xaa)
o xfixes.h (unconditionally, symbols required by dri2)
LoaderSymbol and similar functions now don't have different prototypes,
in loaderProcs.h and xf86Module.h, so that both headers can be included,
without the need of defining IN_LOADER.
xf86NewInputDevice() device prototype readded to xf86Xinput.h, but
not exported (and with a comment about it).
Rather than assuming rules in the CoreKeyboardProc, init the default rules in
InitCoreDevices, then re-use them later.
In the xfree86 DDX, set the rules to "base" or "evdev", depending on whether
we'll load kbd or evdev.
If we create a new MD, use pc105,us as default and re-use the rules file used
previously.
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
The device's button down state array was changed to use DOWN_LENGTH and thus
bitflags for each button in cfcb3da7.
Update the DBSN events to copy this bit-wise state.
Update xkb and Xi to check for the bit flag instead of the array value.
Reported by ajax.
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
This is the biggest "visibility" patch. Instead of doing a "export"
symbol on demand, export everything in the sdk, so that if some module
fails due to an unresolved symbol, it is because it is using a symbol
not in the sdk.
Most exported symbols shouldn't really be made visible, neither
advertised in the sdk, as they are only used by a single shared object.
Symbols in the sdk (or referenced in sdk macros), but not defined
anywhere include:
XkbBuildCoreState()
XkbInitialMap
XkbXIUnsupported
XkbCheckActionVMods()
XkbSendCompatNotify()
XkbDDXFakePointerButton()
XkbDDXApplyConfig()
_XkbStrCaseCmp()
_XkbErrMessages[]
_XkbErrCode
_XkbErrLocation
_XkbErrData
XkbAccessXDetailText()
XkbNKNDetailMaskText()
XkbLookupGroupAndLevel()
XkbInitAtoms()
XkbGetOrderedDrawables()
XkbFreeOrderedDrawables()
XkbConvertXkbComponents()
XkbWriteXKBSemantics()
XkbWriteXKBLayout()
XkbWriteXKBKeymap()
XkbWriteXKBFile()
XkbWriteCFile()
XkbWriteXKMFile()
XkbWriteToServer()
XkbMergeFile()
XkmFindTOCEntry()
XkmReadFileSection()
XkmReadFileSectionName()
InitExtInput()
xf86CheckButton()
xf86SwitchCoreDevice()
RamDacSetGamma()
RamDacRestoreDACValues()
xf86Bpp
xf86ConfigPix24
xf86MouseCflags[]
xf86SupportedMouseTypes[]
xf86NumMouseTypes
xf86ChangeBusIndex()
xf86EntityEnter()
xf86EntityLeave()
xf86WrapperInit()
xf86RingBell()
xf86findOptionBoolean()
xf86debugListOptions()
LoadSubModuleLocal()
LoaderSymbolLocal()
getInt10Rec()
xf86CurrentScreen
xf86ReallocatePciResources()
xf86NewSerialNumber()
xf86RandRSetInitialMode()
fbCompositeSolidMask_nx1xn
fbCompositeSolidMask_nx8888x0565C
fbCompositeSolidMask_nx8888x8888C
fbCompositeSolidMask_nx8x0565
fbCompositeSolidMask_nx8x0888
fbCompositeSolidMask_nx8x8888
fbCompositeSrc_0565x0565
fbCompositeSrc_8888x0565
fbCompositeSrc_8888x0888
fbCompositeSrc_8888x8888
fbCompositeSrcAdd_1000x1000
fbCompositeSrcAdd_8000x8000
fbCompositeSrcAdd_8888x8888
fbGeneration
fbIn
fbOver
fbOver24
fbOverlayGeneration
fbRasterizeEdges
fbRestoreAreas
fbSaveAreas
composeFunctions
VBEBuildVbeModeList()
VBECalcVbeModeIndex()
TIramdac3030CalculateMNPForClock()
shadowBufPtr
shadowFindBuf()
miRRGetScreenInfo()
RRSetScreenConfig()
RRModePruneUnused()
PixmanImageFromPicture()
extern int miPointerGetMotionEvents()
miClipPicture()
miRasterizeTriangle()
fbPush1toN()
fbInitializeBackingStore()
ddxBeforeReset()
SetupSprite()
InitSprite()
DGADeliverEvent()
SPECIAL CASES
o defined as _X_INTERNAL
xf86NewInputDevice()
o defined as static
fbGCPrivateKey
fbOverlayScreenPrivateKey
fbScreenPrivateKey
fbWinPrivateKey
o defined in libXfont.so, but declared in xorg/dixfont.h
GetGlyphs()
QueryGlyphExtents()
QueryTextExtents()
ParseGlyphCachingMode()
InitGlyphCaching()
SetGlyphCachingMode()
I merged the wrong patch. See correct patch at:
http://lists.freedesktop.org/archives/xorg/2008-November/040540.html
Not activating the device before attempting to enable it would leave the
sprite unset, crashing the server when enabling the real devices.
This reverts commit e078901a4e.
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
As proposed by Owen Taylor [1], the enter-leave event model needs to adjust
the events sent to each window depending on the presence of pointers in a
window, or in a subwindow.
The new model can be summarised as:
- if the pointer moves into or out of a window that has a pointer in a child
window, the events are modified to appear as if the pointer was moved out of
or into this child window.
- if the pointer moves into or out of a window that has a pointer in a parent
window, the events are modified to appear as if the pointer was moved out of
or into this parent window.
Note that this model requires CoreEnterLeaveEvent and DeviceEnterLeaveEvent to
be split and treated separately.
[1] http://lists.freedesktop.org/archives/xorg/2008-August/037606.html
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Peter Hutterer <peter.hutterer@redhat.com>
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
Signed-off-by: Adam Jackson <ajax@redhat.com>
EnableDevice and DisableDevice both change the property too.
And enabled must be set to FALSE in AddInputDevice, the device is not enabled
yet.
X.Org Bug 18111 <https://bugs.freedesktop.org/show_bug.cgi?id=18111>
dev->enabled is a Bool. Bool is two bytes.
BOOL on the other hand is a protocol type and always 1 byte. So copy the value
into the one-byte type before passing it into XIChangeDeviceProperty.
Found by Michel Dänzer.
X.Org Bug 18111 <http://bugs.freedesktop.org/show_bug.cgi?id=18111>
The current code exposes to inconsistent updates, i.e. if handler N succeeds
but handler N+1 fails in setting the property, an error is returned to the
client although parts of the server now behave as if the property change
succeeded.
This patch adds a "checkonly" parameter to the SetProperty handler. The
handlers are then called twice, once with checkonly set to TRUE.
On the checkonly run, handlers _MUST_ return error codes if the property
cannot be applied. Handlers are not permitted to actually apply the changes.
On the second run, handlers are permitted to apply property changes.
Errors codes returned on the second run are ignored.
A property can only be deleted if any of the following is true:
- if a property is deletable and all handlers return Success.
- if a property is non-deleteable and the all handlers return Success AND the
delete request does not come from a client (i.e. driver or the server).
A client can never delete a non-deletable property.
For master devices, the ptraccel code could segfault on free since we'd be
dereferencing random memory. Callocing the valuatorClassRec is the easy fix.
Unplug a mouse, then warp the pointer and the warp pointer code will try
to update the position of the last slave device associated with the
master. That pointer will be stale and the X server will crash.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
We may need more than one handler to deal with a property (e.g. one in the
driver, one in the DIX), so get the handlers into a linked list and call them
one-by-one. This is of course slightly less entertaining than the hilarious
WRAP/UNWRAP game we play in other parts of the server.
XIRegisterPropertyHandler/XIUnregisterPropertyHandler are the interface
drivers/the DIX should use to attach themselves to the device.
XIDeleteAllDeviceProperties destroys everything, including the handlers.
Basically just copied from randr properties, with minor changes only.
Each device supports arbitrary properties that can be modified by clients.
Modifications to the properties are passed to the driver (if applicable) and
can then affect the configuration of the device.
Note that device properties are limited to a specific device. A property set
on a slave device does not migrate to the master.
Basically just copied from randr properties, with minor changes only.
Each device supports arbitrary properties that can be modified by clients.
Modifications to the properties are passed to the driver (if applicable) and
can then affect the configuration of the device.
Note that device properties are limited to a specific device. A property set
on a slave device does not migrate to the master.
Using id = 0 only worked pre-MPX since XInput didn't allow XOpenDevice for the
core devices (0 and 1). Now we can now legally register for events so we may
overwrite our device-independent classes with the ones selected for the VCP.
So, increase the EMASKSIZE to MAX_DEVICES + 1 and use MAX_DEVICES as the ID
when we don't have a device.
Mixing usage where some parts of the code treated this field as a bitmask
and other parts as an array of card8 was wrong, and as the wire protocol
wanted bitmasks, it was less invasive to switch the newer counting code use
booleans.
Master devices track slave buttons by waiting for all slave buttons to be
released before delivering the release event to the client.
This also removes the state merging code in DeepCopyDeviceClasses -- that
code was changing master device state without delivering any events,
violating protocol invariants. The result will be that existing slave
button state which does not match the master will not be visible through the
master device. Fixing this would require that we synthesize events in this
function, which seems like a bad idea. Note that keyboards have the same
issue.
Signed-off-by: Daniel Stone <daniel@fooishbar.org>
Signed-off-by: Peter Hutterer <peter@cs.unisa.edu.au>
device->button->down used to be a 32-byte bitmask with one bit for each
button. This has changed into a 256-byte array, with one byte assigned for
each button. Some of the callers were still using this array as a bitmask
however, this is fixed with this patch.
Thanks to Keith Packard for pointing this out. See also:
http://lists.freedesktop.org/archives/xorg/2008-June/036202.html
We only have one set of default rules options in xkb. When the second keyboard
is brought up with Xkb options specified, these new options overwrite the old.
In future server generations, the rules used for the VCK are a mixture of the
default ones and ones previously specified for other keyboards. Simply
resetting the xkb default rules to NULL avoids this issue.
Reproducable by setting XkbLayout "de" and XkbVariant "nodeadkeys". In the
second server generation, the VCK has "us(nodeadkeys)". This again produces a
SIGABRT when the first key is hit.
I could not figure out why the SIGABRT happens. This patch is avoiding the
issue rather than fixing it.
With the MD/SD device hierarchy we need control over the generation of the
motion history as well as the conversion later before posting it to the
client. So let's not let the drivers change it.
No x.org driver currently uses it anyway, linuxwacom doesn't either so dumping
it seems safe enough.
During GetPointerEvents (and others), we need to access the last coordinates
posted for this device from the driver (not as posted to the client!). Lastx/y
is ok if we only have two axes, but with more complex devices we also need to
transition between all other axes.
ABI break, recompile your input drivers.
Sometimes we didn't have a cursor when coming back from suspend. Reason was
that the suspend caused the server to lose the device that was attached to the
VCP, and a RemoveDevice() would then set the cursor to NULL.
Solution: only set the cursor to NULL if we actually own the sprite.
We pass in the client that wants to create the device anyway, lets use the
parameter instead of hardcoding the serverClient.
Wow. I hope this is merge detritus, otherwise it'd be a sign that I didn't
have enough coffee that day.
When a new device is added, calculate the event size needed if a DCCE event is
sent and set the EQ's event size to this minimum. This avoids reallocs when a
event is sent (which may happen during a SIGIO).
This variable was used originally to determine which client is allowed to
change the pointer-keyboard pairing. For now, we just let anyone change it and
see how that works out.
Rather than freeing/allocing classes each time the device capabilities need to
swap, store them in the devPrivates system.
When a class is unused, it is pushed into the devPrivates, and later recovered
when needed again. This saves us a lot of memory allocations/frees, admittedly
on the cost of some memory.
The DDX (xfree86 anyway) maintains its own device list in addition to the one
in the DIX. CloseDevice will only remove it from the DIX, not the DDX. If the
server then restarts (last client disconnects), the DDX devices are still
there, will be re-initialised, then the hal devices come in and are added too.
This repeats until we run out of device ids.
This also requires us to strdup() the default pointer/keyboard in
checkCoreInputDevices.
X.Org Bug 14418 <http://bugs.freedesktop.org/show_bug.cgi?id=14418>
The device classes aren't deleted anymore on a class change, so there's no
need to store the MD's original classes. We should however restore the MD to
sane defaults when disconnecting the last device, consider this as TODO item.
Instead of a simple counter, use bits to keep track of which device is where
etc. When device enters a window (or sets focus), the bit matching the device
is set, when it leaves again, it is unset. If there are 0 bits set, then
Leave/Enter/Focus events may be sent to the client.
Same theory as before, but this should get around the insanity with
Grab/Ungrab special cases. Those cases are basically untested though.
InitializeSprite won't create a new one if it already exists, with the result
of overwriting the master's sprite. This master sprite is then assigned to the
floating slave, and freed when the slave is reattached later.
Setting the sprite to NULL forces InitializeSprite to alloc a new one, and
this one can be freed without further repercussions.
XkbFinishDeviceInit does the following:
xkbi->kbdProc= pXDev->kbdfeed->CtrlProc;
pXDev->kbdfeed->CtrlProc= XkbDDXKeybdCtrlProc;
If we directly copy the device classes for the VCK, pXDev->kbdfeed->CtrlProc
at the time of copying is still XbkDDXKeybdCtrlProc. So at some point
XkbDDXKeybdCtrlProc is called, and calls itself, and calls itself, and...
Setting the device's classes to NULL seems to fix things. The memory isn't
lost, it gets stored into the devPrivates and freed at device closing time.
Before we enable the device through the driver, we size it up and make sure
that the events in the event list contain enough bytes for a possible
ClassesChangedEvent lateron.
If two devices are attached to the same master device, pressing button 1 on
each of them leads to two button presses from the same device. Some apps
really don't like that.
So we just put a counter in place and only send the first press and the last
release.
We free the ValuatorClassRec quite regularly. If a SIGIO is handled while
we're swapping device classes, we can bring the server down when we try to
access lastx/lasty of the master device.
XkbInitKeyboardDefviceStruct may call FatalError if it fails. FatalError then
cleans up all the devices, resulting in a segfault if the pointer is
uninitialised.
Old code was fundamentally broken, fixes now are:
- free the MDs current device classes
- copy the device classes instead of flipping the pointers
- check for the old MD, not the new one.
Anything in dev->key, dev->valuator etc. of a MD must always be a copy of the
original class. The intial classes of an MD (the ones set up before an SD is
attached) as well, as we may have to restore them if no SD is attached
anymore.
Each time a different slave device sends through a master, an
DeviceClassesChangedEvent is enqueued. When this event is processed, all
classes of the matching master device are changed, and the event is sent to
the clients.
Next time the master is queried, it thus shows the evclasses of the last slave
device. The original classes are stored in the devPrivates.
TODO: if all slave devices are removed, the master's original classes need to
be restored.
For pointers: don't try to set master->valuator fields if there is no master.
For keyboards: check if device is valid before trying to access the fields in
miPointerGetScreen (btw. this disables DGA events for floating keyboards).
Also stop the hideous number of ErrorFs if we request the paired device for a
floating dev.
XkbRemoveResourceClient wants to access xkbInfo if it exists, so make
sure we NULL it after freeing it. It doesn't make much sense to move
the RemoveResourceClient call first, as there's not much point in
notifying clients while we're shutting the server down anyway.
Floating devices get sprites, but still aren't spriteOwners. This prevents
them from getting rendered, and also stops segfaulting.
(not really solving the problems with keyboards though)
Set isMaster for VCP/VCK.
Init sprites for master pointer devices.
Pair master kbds with master pointers (1:1 pairing!).
Attach other devices to VCP/VCK.
For now, we don't allow attaching slaves to other slaves, and we don't allow
pairing slaves with other slaves.
Pairing is for master keyboard->master pointer only.
Attaching is for slave device->master device only.
We re-pair them with the VCP, not a real device! If we would do otherwise,
somebody may change our keyboard focus and thus get us typing where we don't
want to type.
If the pairing client is not set, then the pairing is initiated internally
(e.g. when a new keyboard device is configured). In this case we _must_ pair
regardless of who is the pairing client.
Unfortunately, more information is needed to properly label the device.
This will come from the configuration file, the hotplug messages, etc.
It will either have to be passed into this function,
or this hook moved down into the callers.
Removes "LookupKeyboardDevice" and "LookupPointerDevice" in favor of
inputInfo.keyboard and inputInfo.pointer, respectively; all use cases
are non-XI compliant anyway.
We need it unconditionally in a few places, and the rest checked for NULL and
then set it to VCK anyway. So, fixing up all callers to appreciate the defined
return value.
EnableDevices is (amongst others )called after a VT switch. We must not create
a new sprite or re-pair the device, otherwise we lose the input device setup
that we had before the VT switch.
This requires the devices to be in exactly the same order as before
the VT switch. Removing a device while on a different VT is probably a bad
idea.
The device state needs to be changed while processing the XI event. Core
events are always processed after XI, so by then the device is already set up
properly. However, we now rely on DeviceButtonMotionMask to be equal to
ButtonMotionMask. It already is, but stick a big fat warning in so nobody
attempts to change it.
This commit disables XKB for the VCK, thus essentially for all devices.
Temporarily anyway.
Add keyc->postdown, which represents the key state as of the last mieqEnqueue
call, and use it when we need to know the posted state, instead of the
processed state (keyc->down). Add small functions to getevents.c to query and
modify key state in postdown and use them all through, eliminating previously
broken uses.
over to new system.
Need to update documentation and address some remaining vestiges of
old system such as CursorRec structure, fb "offman" structure, and
FontRec privates.
Add support for HAL-based hotplugging, in which we just get the list of
input devices and properties from HAL. Requires an FDI which is not yet
in mainline HAL.
Is set when passive grab is implicit as result of a ButtonPress event. If this
is the case, we need to store the XI mask as well as the core mask to ensure
delivery of XI events during the grab's lifetime.
Remove all core grabs on other devices when client issues a GrabPointer or
GrabKeyboard request. Let's assume that the client really only wants one
device to interact, so this seems like a reasonable solution.
Add XGE handling in DeliverGrabbedEvent.
We can now grab something selecting XGE events, but the current code is a
bit messy and doesn't work too well yet.
If we don't do this, a device that is paired before a sprite has been
initialized for the paired device will not actually get the right sprite and
segfault the server on focus events. Happens for the VCK.
Both VCP and VCK are not in the inputInfo.devices list anymore, so we need to
check them separately. If we don't do this, we end up re-using ids 0 and 1,
causing all sorts of grief for clients.
Requires moving the spriteTrace into the DeviceIntRec and adjusting a few
functions to take in device argument, most notably XYToWindow().
Cursor rendering on the second screen is busted.
arbitrary X status codes instead of just TRUE/FALSE.
The dix layer in most cases still does not propagate the return value of
XACE hooks back to the client, however. There is more error propagation
work to do.
Improve memory usage by allocating the sprite's memory only to devices that
actually have a sprite and provide means to remove a device's cursor from the
screen (more hotplugging, yay!).
This commit breaks ScreenRec's ABI.
The former <X11/extensions/XKBsrv.h> has been pulled into the server now as
include/xkbsrv.h, and the world updated to look for it in the new place,
since it made no sense to define server API in an extension header. Any
further work along this line will need to do similar things with XKBgeom.h
and friends.
EnableDevice.
zero out spriteTrace, otherwise GetCurrentRootWindow() may return
invalid data.
Evdev adds previously hotplugged devices on its own when rescanning,
and ActivateDevice does not get called for those devices. Sprites need
to be initialized or paired before the device gets started, so the
safest place to do so is EnableDevice (which actually does get called
by the evdev driver).
dix: IsPointerDevice and IsKeyboardDevice, use same ways to identify type
of device as XI does for the XListInputDevices reply.
Autopair each non-pointer device with VCP when activating, pair with
real device after activation.
Don't return non-keyboard devices when calling GetPairedKeyboard or
PickKeyboard, otherwise we segfault for 'evdev brain'.
state field in the event, rather than using the virtual devices.
ProcessPointerEvent: name argument "device" instead of "other".
Add GetPairedKeyboard().
otherwise a Xi grab may overwrite or release a core grab.
Replace grab and associates with coreGrab and deviceGrab structures,
adjust rest of dix/Xi/etc to compile.
xfree86: Don't check for core devices, we'll have the virtual ones anyway.
If we check, the first mouse device is duplicated and sends
double events.
dix: set coreGrab flag for grabs caused by GrabPointer and button presses.
remove virtual core devices from device list, only real devices are in
the list now.
Auto-pair each keyboard with a real pointer if one is available,
provides multiple keyboards automatically after startup if devices
are configured.
fix GuessFreePointerDevice() to do what it's supposed to do.
mi: fix: call miPointerMove from miPointerWarpCursor.
fix: remove unused id field from miCursorInfoRec
don't update sprite for virtual core pointer.
ambiguious request. PickPointer and PickKeyboard are used for getting
the appropriate pointer when situation is unclear.
Fix some issues with InitializeSprite.
dix, xfree86: Remove last traces of InitSprite.
Free sprite struct if a spriteOwner is paired.
xfree86: Use PairDevices instead of passing booleans around when creating a
sprite.
Xext: Switch back to using LookupPointer/KeyboardDevice instead of
inputInfo.xyz.
Adding PointerKeyboardPairingChanged event
Correct error values for XWarpDevicePointer
dix: Adding device argument to SendMappingNotify
Adding spriteOwner flag to devices
Add a generic 'ring the bell' function (console bell on Linux and BSD,
/dev/audio on Solaris), and add DDX functions for this. Make this the
core keyboard's bell.
Port Xvfb and Xnest to this.
Port XFree86 to this, with OS-specific hooks for Linux, BSD, and Solaris
taken from foo_io.c in the old layer.
Update the DEVICE_ABS_CALIB stuff to include the new elements.
New DEVICE_ABS_AREA support.
dev->touchscreen becomes dev->absolute, with _CALIB and _AREA stuff in it.
Update xfree86 to compile with this, kdrive needs an update too.
Add devices in forward order with the normal linked list convention.
Previously, AddInputDevice would add all the devices in reverse order to
off_devices, before they were added again in reverse order to devices with
EnableDevice.
This just makes both work in forward order, which provides the ordering as
you'd expect when hotplugging devices (i.e. adds them to the head, not the
tail).
Allow new devices to be added after a device that _wasn't_ the last on the
list was removed, by ensuring inputInfo.numDevices always increases, and
never decreases.
Initialise our axes properly in the DIX, and make sure we don't
unnecessarily clip maxval when it's not set.
Fix keymap copying in Xephyr (to some degree: it's still broken),
and set nAxes and nButtons properly.
Add XSERV_t, TRANS_SERVER, TRANS_REOPEN to quash warnings.
Add #include <dix-config.h> or <xorg-config.h>, as appropriate, to all
source files in the xserver/xorg tree, predicated on defines of
HAVE_{DIX,XORG}_CONFIG_H. Change all Xfont includes to
<X11/fonts/foo.h>.
change "foo.h" to <X11/foo.h> for core headers, e.g. X.h, Xpoll.h;
change "foo.h", "extensions/foo.h" and "X11/foo.h" to
<X11/extensions/foo.h> for extension headers, e.g. Xv.h;
change "foo.[ch]" to <X11/Xtrans/foo.[ch]> for Xtrans files.
xc/programs/Xserver/dix/colormap.c
xc/programs/Xserver/dix/cursor.c
xc/programs/Xserver/dix/devices.c
xc/programs/Xserver/dix/dispatch.c
xc/programs/Xserver/dix/dixfonts.c
xc/programs/Xserver/dix/dixutils.c
xc/programs/Xserver/dix/events.c
xc/programs/Xserver/dix/extension.c
xc/programs/Xserver/dix/gc.c
xc/programs/Xserver/dix/glyphcurs.c
xc/programs/Xserver/dix/grabs.c
xc/programs/Xserver/dix/main.c
xc/programs/Xserver/dix/pixmap.c
xc/programs/Xserver/dix/privates.c
xc/programs/Xserver/dix/property.c
xc/programs/Xserver/dix/resource.c
xc/programs/Xserver/dix/swaprep.c
xc/programs/Xserver/dix/swapreq.c
//bugs.freedesktop.org/show_bug.cgi?id=2560) attachment #2037
(https://bugs.freedesktop.org/attachment.cgi?id=2037) ANSI-fy
Xserver/dix code. The conversion preserves the comments which annotate
variables. These have been moved into doxygen(esque?) "stubs" above
each function. Patch by Mike Owens <etc@filespanker.com>.